Question about 1998 Chevrolet S-10 Pickup

1 Answer

How to set the timimg on a 98 blazer - 1998 Chevrolet S-10 Pickup

Posted by on

  • louis bailey May 11, 2010

    what size engine?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 180 Answers

The timing is not adjustable! factory set!

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 97 blazer rear end fit in a 98 blazer


As long as the trim and model is the same I don't see why not. I assume you're talking about what used to be called the S-10. There's only been 2 real generations of the blazer which changed in 94. There were a few cosmetic changes between the 97 and 98 but all in all it's the same vehicle.

Nov 14, 2014 | 1998 Chevrolet Blazer

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

1 Answer

How hard is it to swap from a 97 blazer core support to 98 blazer support


anything is possible with a bit of inginuety and set of gas bottles

Jan 13, 2011 | 1997 Chevrolet Blazer

1 Answer

89-98 chevy blazer


It's not worth doing all that conversion, buy the time you spend the time and money to convert the 89 4.3 to work on the 98 blazer, it would be cheaper to install a 98 vortec rebuild. The 89 4.3 have a TBI fuel injection system and the ecm on the 98 will not work and the bad news is that the ecm on the 98 also controls the transmission shift points and the 89 will not, so even if you swap the ecm to have the 89 4.3 engine work. the transmission will not shift. Sorry for the bad news but it would be cheaper to replace the 98 engine with the years of 1996 to 2001. Good luck and hope this helps. 

Jul 21, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

Can't get alternator out of 98 Blazer LS


There are 2 bolts on the front bottom one on the back upper corner. Once removed you 2 pry bars one on ech side and it should come right out they fit tight in the bracket

Mar 07, 2009 | 1997 Chevrolet Blazer

4 Answers

What transmission interchanges with a 98 4z`x4 Blazer


sorry but your stuck with the 4l60e if you want it to be right. as for using the bravada transmission thats fine you just have to use your transfer case. your transfer case uses a switch on the dash and an electric motor on the transfer case. the bravada uses a series of sensors on the front and rear axle that sense wheel slippage and send a signal to the electric motor on the transfer case causing it to lock in four wheel drive. when the sensors dont sense wheel slippage any more the system returns to two wheel drive. that,s why they call it smart track. just unbolt your transfer case from your transmission and bolt it to the bravada transmission and install it. p.s- dont forget to at least change the front pump converter seal. for 4 or 5 bucks it,s cheap insurance against a major leak and i dont think you want to pull that transmission out again and yes i saw that happen to many times. good luck.-G.J.M

Jan 04, 2009 | 1998 Chevrolet Blazer

2 Answers

98 chevy Blazer Turn Signals quit


try working you hazard light switch a few times this will cause the turn signals to lose contact. it is a common problem

Dec 15, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...