Question about 1996 GMC Suburban

1 Answer

Left front brake not always releaseing - 1996 GMC Suburban

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

Need to grease caliper pins or rubber brake line is breaking down on the inside,do caliper pins first

Posted on Apr 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is next? Brake pressure is non-existent on all but front left. Pedal pressure is very hard. Replaced all calipers and master cylinder. Fluid does not exit nipple when bled on all but left front.


Its possible that your rubber lines are collapsed. I've had them keep fluid from going thru as well as not releasing pressure. See if fluid gets to caliper thru rubber. You can plug it with your finger and release pedal. If you feel vacuum and fluid flows well when you push brake, that's probably not the problem. Its somewhere to start tho.

May 31, 2014 | Ford SVT Cars & Trucks

1 Answer

I tried to bleed the brakes rf good lf no fluid comes out.replaced rf line working good,pulled line from master cyl. and pulled bleeder valve no fluid. i have a 99 cavilier with abs,any idea.i havent tried...


Im confused first thing is to connect all lines, fill master and start bleeding at master, have someone pump brake three times and hold, open line at master allow fluid or air to flow and close, do not leave open to long,after 3 sec of fluid flow close line. you will do this to every line on the master. pumping the pedal three times and holding down pedal every time you open the line , after bleeding master you will then go to the left front as this is the brake with no fluid flow. you will make sure brake fluid is full always check after a few bleedings.

Remove the bleeder screw and place finger over the hole. tell them when to go down and when to let up, this may take a while if a lot of air is in system, remove finger and tell them to push down then put finger over hole and tell to release then tell them to push as they push release finger, you will need to do this until you get fluid flow making sure when pedal is released that hole is covered with finger so that air is not sucked into system. once you get a flow you will put bleeder in and bleed that wheel, if bleeding is good you will then bleed system starting at rt rear then left rear and then rt front and last left front.

Dec 25, 2012 | Cars & Trucks

1 Answer

1999 Yamaha Kodiak Front Disc Brake - Rebuilt master cylinder with new parts. Replaced orings on piston in front caliper and bleed brakes using new fluid. The piston will not retract. What is proble


The brake hose is clogged. When under pressure from applying breaks, the piston is forced tight to the rotor. When released the fluid will not return through the hose because there is no real pressure. Replace the hose.
murf427

Jul 31, 2012 | Cars & Trucks

2 Answers

How do you bleed the brakes on a 1996 pontiac sunfire se


right rear,left rear,right front,left front wheels.

Jan 19, 2011 | 1996 Pontiac Sunfire

1 Answer

Changed front brakes on 2000 grand cherokee, bled brakes, and pedal seems spongier than normal


You still have air in the brakes,start at the master cylinder,then the rear,right wheel,left rear,and right front,then the left front.Make sure the calipers are releasing completely ,if they are not,then a brake hose could be bad.

Feb 04, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Front brakes not releasing properly.


Sounds like the caliper needs replaced. Sometimes the pistons lock in the caliper and cause the brakes to drag. When the mechanic changed the brakes before, he pushed the pistons in all the way to accomodate the new brake pads. Now that they are wearing back down, it is getting to the warped spot in the caliper and starting to stick.

Jun 25, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Brakes wont release


Was the leading input shaft adjusted correctly? Usually they come with a new one and has to be matched in length to your old one. If the old one was used I would bleed the system from the right rear, left rear, right front, & left front in that order. Always bleed from the furthest point first. Sometimes air in the lines will lock these up

May 24, 2009 | 1992 Ford F350

1 Answer

Front left caliper geting stuck and slowly releases replaced caliper alredy


SOUNDS LIKE YOU NEED A NEW LF FLEXHOSE..COLLAPSED INTERNALLY AND RESTRICTING BRAKE FLUID WHEN YOU RELEASE BRAKE PEDAL

May 04, 2009 | Plymouth Acclaim Cars & Trucks

1 Answer

Slow releasing left front brake


Your master cyl. may not be sending the fluid to the brake system like it should.

Jun 30, 2008 | 1992 Oldsmobile Ninety Eight Regency

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...