Question about 2008 Buick Lacrosse

1 Answer

Can you please give me the specific oil required for the vehicle?

Posted by on

  • nzdfwo Apr 28, 2010

    Sorry can you please tell me if there is a specific grade of oil required for this vehcile when doing an oil change? That is SAE30 or likewise

  • czitzow1976 May 11, 2010

    im not sure what you mean??

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 819 Answers

5w30 conventional, minimum rating SM (all modern quality automobile oils will hold this rating). you may use any brand, try to stick to a major brand. you can also use synthetic oils, which use the same rating system, but provide further protection for your engine. hope this is helpful!

Posted on Apr 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water in the oil


Water in the oil is caused by:
  • Cracked Head
  • Cracked Block
  • Blown Head Gasket
  • Intake manifold leak (some cars)
You don't give specifics on your vehicle, but these are the most common causes of water in the oil. All will require so,e level of engine disassembly to locate and correct the problem.

Sep 07, 2014 | Cars & Trucks

1 Answer

Oil pan bolt torque


oil pan bolts are torqued in inch lbs due to their size and usually doesn't require a specific torque value. all bolts in a manual does show torque settings in all applications.However because of its non critical application a specific value is not necessary. a "snug" tightness is adequate with proper gasket/sealer in place to prevent seepage or leaks. in that area of the engine,leak can come from almost anywhere. top,front,or even rear of the engine blown by the wind a car creates while in motion. oil sensors{ but not limited to} are notorious for leaks as the vehicle ages particularly in that area. steam clean or thoroughly degrease the area and run the engine a few miles and recheck the area before proceeding to make repairs.

May 27, 2014 | 2001 Nissan Pathfinder

1 Answer

Require torque settings for a hyundai tucson 2008,gls petrol engine


Specifically which torque settings are you referring to. There are thousands to choose from. Please give an example such as "differential carrier", "cylinder head", "exhaust manifold to engine block" etc.

Mar 31, 2012 | 2008 Hyundai Tucson

2 Answers

The check engine light is staying on. All the fluids have been topped up. Any ideas


Please see my tip at http://www.fixya.com/cars/r5932051-check_engine_light_check. These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Feb 04, 2011 | 2003 Kia Rio

1 Answer

Oil leak


You have to differentiate whether the oil leak is from the engine or the tranny. After determining where the source, you must isolate the specific area; timing belt area, the middle-between the engine and the tranny. This can be cheaply determine by placing white piece of paper underneath the engine and observe the droppings of oil. Oil leak repair can be costly-especially an oil starved engine, so isolating the source is essential and tear-down might required.
Due to the age of the vehicle, possible sources are the camshaft seal, crankshalf seal, oil pan gasket, crankshaft end seal,distributor o-ring, and valve cover gasket.
In addition, other oil leaks can come the transmission, and power steering pump and rack'n'pinion. Best to raise the vehicle and inspect undercarriage of vehicle.

Oct 29, 2010 | 1998 Honda Civic

1 Answer

How do I check and possibly replace the engine oil pressure sensor in a 2006 GMC Envoy Denali?


Oil Pressure Test Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge. A tachometer may also be needed, as some specifications may require running the engine at a specific RPM.
  1. While the engine is cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Note and record the oil pressure reading when the engine is cold. The engine may need to run at a specified RPM, if so check the vehicle's specification.
  5. Run the engine until normal operating temperature is reached.
  6. Check the oil pressure reading again with the engine hot and record the value. Turn off the engine.
Compare the hot oil pressure reading to the specification. If the reading is low, check the cold pressure reading against the specification. If the cold pressure is well above the specification, and the hot reading was lower than the specification, the engine may have the wrong viscosity oil. Change the oil, making sure to use the proper grade and quantity, and then repeat the test.
Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Oct 09, 2010 | 2006 GMC Envoy Denali

1 Answer

Oil preassure indicator blinking on minimun RPM engine, reading is almot 0, if press throtle will stop blinking


Get a pressure gauge and see what type of pressure this this vehicle is giving you at idle and at about 2000 RPM's. Your gonna have to remove the oil pressure sending unit/switch to screw in the pressure gauge. If its giving you the prescribed pressure while testing, worse case scenario is over. ( oil pump, engine wear) If your not getting the prescribed pressure with the testing gauge, its either the oil pump or engine wear or both. Have a Certified ASE Technician look over the vehicle if this is the out come. There is additional testing to be done which requires additional tooling expertise in this area.

Now if the pressure was within spec's with the test on gauge, its either the switch, the wiring to and from the gauge or the gauge itself. Get the Shop Repair manual for this vehicle for Oil pressure specifications as well as additional testing of switch , circuitry and gauge. This is fun stuff . Wear gloves and eye protection while removing the switch and screwing in the testing gauge and vise versa after testing is completed. Good luck

Mar 26, 2010 | 1992 Chevrolet S-10 Blazer

1 Answer

I need a diagram of how to relace oil pump


Removal of Oil Pump
Note: While this task is possible when the engine is in place in the vehicle, in practice, it requires so much preliminary disassembly, and is so difficult to perform due to the restricted access, that owners are advised to remove the engine from the vehicle first.
NOTE: However, that the oil pump pressure relief valve can be removed with the engine in place.
If you have required tool's, engine stand, engine lift if you have them I can give you directions how to remove it.
Please let me know if this is of any HELP.

Feb 21, 2010 | 1999 Ford Contour

1 Answer

Oil consumption-1 Qt/1000 miles-50k on vehicle 2005 Hyundai Tuscon


Are you using the correct weight oil as outlined in your owner's manual. You car is unusual in that the specifications require you to use 10w40 oil when driving above −13 degrees fahrenheit. It also states that you are to use 5w20 when operating the vehicle in temperatures below 14 degrees fahrenheit. Then goes on to say not to be used for sustained high speed operation. So all in all the specifications for your vehicle are odd in that most vehicles today use 5w20 weight oil. I personally would use 10w40 or 10w30 weight in this engine as that would be appropriate for the vast majority of how and where you drive. If you are using a lighter weight oil that may be why it is using oil at this rate

Nov 16, 2009 | 2005 Hyundai Tucson

2 Answers

What size oil filters do i use for cars


You use whatever oil filter is specified for that specific vehicle.
Thanks,
Lee

Sep 14, 2009 | 1991 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...