Question about 2002 Chevrolet Blazer

1 Answer

Evap system where all the areas to check , to replace

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 623 Answers

I would find a garage that can perform a smoke test on the evap system. They inject smoke into the system and look for where it comes out.

Posted on Apr 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is the EVAP System vale on Honda odyssey 2003


This code indicates a leak in the evap system. The first thing to check is the gas cap-is it on tight? If yes, check vacuum hoses under the hood. A loose or degraded hose on the purge valve will also cause this code. The purge valve looks like the pic below and has one hose going to the engine and the other going to the vapor cannister.
download-dwbgzyjx1s1bj3innjxcfx0i-3-0.jpg

Jun 15, 2017 | Honda Cars & Trucks

1 Answer

Hyaunda 2010 check engine light code P0442


code p0442 has 2 possible fault areas

evaporative emission (EVAP) system --small leak detected===causes --hose connection/s--intake leak--EVAP canister--EVAP canister purge valve
and the second possible

evaporative emission system--large leak detected (fuel cap loose/off)===causes--mechanical fault---hose connection/s---EVAP pressure sensor

May 16, 2014 | 2002 Subaru Impreza

1 Answer

Evap code p0441


Error Code: P0441
Fault Area:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Feb 06, 2014 | 2003 Toyota Land Cruiser

1 Answer

Mechanic said that there is a small leak in the system according to their computer but was told the leak was too small using a tracer. Any suggestion. They've replaced the gas tank cap but no luck. ...


I assumes, since you mentioned the cap, that you are refering to the Evap System.
There is not much to look at within the Evap System.
Check and make sure someone did not puncture your filler neck to steal gas. That usually gives a large leak but it does not hurt to check.
Also what kind of cap did they replace it with? The Stant locking caps are good for those small leaks. If your area does smog inspections then a smog station may be kind enough to check your cap on their vacuum machine.
Then start at the intake and check the Evap line and follow it to the purge canister and its hoses.

Aug 23, 2011 | 2003 Nissan Frontier Crew Cab

1 Answer

I have a 04 Aveo with 120,000 miles on it. The check engine light came on and it threw a code P0441. It only pops on when I put gas in it. I replaced the gas cap and purge solenoid near the gas tank. It...


This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP purge valve OFF, closed, and the EVAP vent valve ON, closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If the vacuum in the EVAP system is more than a predetermined value within a predetermined time, DTC P1441 will set.

Check The Evap purge valve for leakage.

Jan 27, 2011 | 2004 Chevrolet Aveo

2 Answers

I need an answer for engine code P1457 auxiliary emission control


CODE P1457 EVAP SYSTEM LEAK DETECTED CANISTER AREA 5 POSSIBLE CAUSES 1- EVAP CANISTER IS LEAKING DAMAGED OR FULL OF WATER. 2- EVAP CANISTER PURGE LINE IS LOOSE DAMAGED OR BLOCKED. 3 - EVAP TWO WAY VALVE OR ORVR VENT SHUT VALVE IS DAMAGED. 4 - EVAP FUEL TANK VAPOR CONTROL VALVE IS DAMAGED OR HAS FAILED. 5 - PCM HAS FAILED.

Sep 06, 2010 | 1998 Honda Accord

3 Answers

Emission control malfuction p0440


Easier said then done without professional tools

However, I'll start you will some theory, then the shop manual procedures followed by some "common" problems

Theory:
Evaporative leak detection strategy is based on applying vacuum to EVAP system and monitoring vacuum decay. Powertrain Control Module (PCM) monitors vacuum level by means of fuel tank vacuum sensor input. At a predetermined time, EVAP purge solenoid and EVAP vent solenoid are turned on. This allows engine vacuum to draw a small vacuum on entire EVAP system. Whenever a sufficient vacuum level cannot be achieved, a large leak or faulty EVAP purge solenoid is indicated.

Conditions for setting this DTC are as follows:
No TP sensor, ODM, IAT sensor, or MAP sensor DTCs present.
Start-up ECT 40-86°F (4-30°C).
Start-up ECT not greater than 14°F (8°C) greater than start-up IAT.
Start-up IAT not greater than 4°F (2°C) of start-up ECT.
Fuel tank level is 15-85 percent.
BARO is greater than 75 kPa.
Vehicle has been driven at least 11 miles.
EVAP system is unable to achieve or maintain vacuum during diagnostic test.

Diagnostic Procedures
1.) Perform On-Board Diagnostic (OBD) system check.
After performing OBD system check, go to next step.

2.) Check if DTC P1665 or P1676 is also set. If any of DTCs is present, diagnose affected DTCs. If DTCs are not present, go to next step.

3.) Turn ignition off. Remove fuel filler cap. Turn ignition on. Using scan tool, observe fuel tank pressure. If fuel tank pressure is zero in. H2O, go to next step. If fuel tank pressure in not zero in. H2O, diagnose evaporative system.

4.) Replace fuel filler cap. Using scan tool, capture FAILURE RECORD data for DTC P0440 and clear DTC. Command EVAP vent solenoid on. Connect EVAP Pressure/Purge Diagnostic Station (J-41413) to EVAP service port. Pressurize EVAP system using diagnostic station. Monitor pressure on EVAP pressure gauge on diagnostic station. If pressure is 5 in. H2O, go to next step. If pressure is not 5 in. H2O, go to step 6.

5.) Maintain EVAP pressure at 5 in. H2O. Observe fuel tank pressure on scan tool. If fuel tank pressure reading on scan tool is 5 in. H2O, go to step 8. If reading is not 5 in. H2O, go to next step.

6.) Disconnect fuel tank vapor line and EVAP purge line from EVAP canister. Block canister fitting for fuel tank pressure line. Connect a hand-held vacuum pump to canister fitting for EVAP purge line. Ensure that EVAP vent solenoid is still commanded on. Apply vacuum to EVAP canister. If vacuum can be maintained at 5 in. Hg, go to step 11. If vacuum cannot be maintained at 5 in. Hg, go to step 10.

7.) Check for restriction in fuel tank vapor line or EVAP purge line. Repair as necessary. After repairs, go to step 16. If restriction is not found, diagnose EVAP system.

8.) Disconnect vacuum source line at EVAP purge solenoid and plug vacuum source fitting on solenoid. Using scan tool's output tests function, select and activate SYSTEM PERF. Pressurize EVAP system to 5 in H2O. Observe EVAP pressure gauge on diagnostic station while removing plug from EVAP purge solenoid vacuum source fitting. If EVAP pressure decreases to zero in. H2O within 15 seconds while system performance is activated, go to next step. If EVAP pressure does not decrease to zero in. H2O within 15 seconds, go to step 13.

9.) Install vacuum gauge on EVAP diagnostic station to vacuum source line. Start and operate engine to greater than 2000 RPM. Observe source vacuum level. If vacuum level is greater than -15 in. Hg, If vacuum level is not greater than -15 in. Hg, go to step 14.

10.) Check for disconnected or damaged vent hose. Check for damaged EVAP canister. Repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

11.) Check for faulty or missing fuel filler cap. Check for disconnected or leaking fuel tank vapor line. Check for disconnected or damaged EVAP purge line. If problem is found, repair as necessary. After repairs, go to step 16. If no problems are found, go to next step.

12.) Using scan tool, command EVAP vent solenoid on. Continuously attempt to pressurize the EVAP system by leaving the EVAP diagnostic station control knob in the pressurized position. Using the Ultrasonic Leak Detector (J-41416), locate and repair leak in EVAP system. After repairs, go to step 16.

13.) Replace EVAP purge solenoid. After replacing solenoid, go to step 16.

14.) Check for carbon release into the EVAP system. Repair as necessary. After repairs, go to step 16.

15.) Replace EVAP vent solenoid. After replacing solenoid, go to next step.

15.) Turn ignition on. Using scan tool, command EVAP vent solenoid on. Using EVAP diagnostic station, pressurize EVAP system to 15 in. H2O. Move rotary switch in diagnostic station to HOLD and observe EVAP pressure gauge. If EVAP pressure decreases to less than 10 in. Hg within 2 minutes, repeat step 3. If EVAP pressure does not decrease, system is okay.

Diagnostic Aids
Check for the following:
Cracked or punctured EVAP canister.
Damaged or disconnected source vacuum line, EVAP purge line, vent hose, for fuel tank vapor line.
Poor connection at PCM.
Inspect harness connectors for backed-out terminals, improper mating, broken lock, damaged terminals, or poor wire connection.
Check for intermittent in circuit.
Check for kinked, pinched or plugged vacuum lines to EVAP purge or fuel tank vapor line. Also check for restrictions.
Faulty or damaged evaporative canister.

Apr 28, 2010 | 1999 Buick Century

2 Answers

P0455 evap emission control system leak (large) on 2000 VW beetle


EVAP evaporative emissions systems monitoring
This system includes the on-board refueling vapor recovery (OVRV) system with leak detection (LDP) pump.

The ORVR system filters fuel vapor through the EVAP canister to prevent vapor escaping directly into the atmosphere.

The engine Control Module (ECM) determines when appropriate conditions are met and activates the LDP to pump a small amount of air pressure into the fuel tank and lines. The pump runs until a pre-determined pressure or time is reached. If the system does not hold the pressure, a fault or DTC is stored in the ECM.

The area this is located is behind the right plastic rear wheel liner cover. You will see the fuel filler neck from there and the rest of the EVAP system. Visual check for cracks on all the hoses specially the hose clamps. There are 3 lines connected to the Activated charcoal canister (EVAP canister fastened to body) that are detachable and use O-rings for secured sealing. Check if O-rings, if damaged, replace.

Apr 18, 2010 | 2000 Volkswagen Beetle

1 Answer

2004 Chrysler Sebring with engine error code 441, what does that indicate?


evap emissions control system incorrect purge flow --the most common chrysler fix for this code is replace leak detection pump /ldp but have it checked first-- other areas are evap lines /canister-- purge solenoid-- vacuum switch

Oct 21, 2009 | 2004 Chrysler Pacifica

1 Answer

2000 ford taurus gas tank has what appears to be a fitting on the top right rear that has hoses attached. there are stains and gas smell coming from this area. my repair manual mentions a plastic push...


The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

Notes: Check for audible vacuum noise in the engine compartment or significant fuel odor in the engine compartment or near the EVAP canister.

On my '98 4x4, the cannister purge valve is located under the hood, mounted on the driver's side fender.

The EVAP cannister itself is located underneath the truck, in back, between the spare tire and the truck bed (have to remove the spare to get at it).

If it were me I would hold off on replacing parts...I'd drive around some more first, making sure that I don't overfill the gas tank or run it dry and making sure I replace the gas cap properly, etc. If the code returns, then its time to think repairs.

Jul 02, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...