Question about 1986 Chevrolet Corvette

1 Answer

New brakes on corvette, now I don't have brakes, brakes have been bleed

Posted by on

  • c-peter5 May 11, 2010

    need more info!!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

More info is needed. What did you replace front or rear brakes

Posted on Apr 28, 2010

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

How to fix1977 corvette stuck front caliper?


replace both calipers and bleed system. remove wheel, unbolt brake flex hose where it mounts to the caliper,clamping hose to keep from losing brake fluid, unbolt caliper from caliper mounting bracket. and remove caliper. re-install in reverse order bleeding front brakes making sure master cylinder doesn`t run out of brake fluid.

Sep 03, 2014 | Cars & Trucks

1 Answer

How to bleed front caliper on 1981 Corvette


Fill master remove bleeder have somebody rapidly pump brake pedal while you hold your finger over the hole. within ten pumps (usually) fluid should come out.By holding your finger over the hole you will feel air pressure let that pass Then do your manual bleed.If still nothing check the rubber line sometime they get messed up inside and fluid will not go through

Aug 22, 2014 | 1981 Chevrolet Corvette

1 Answer

98 corvette what is the proper procedure to bleeding the brakes


  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  7. Bleed the base brake system. Follow the scan tool directions until the desired brake pedal height is achieved.
  8. If the bleed procedure is aborted, a malfunction exists. Perform the following steps before resuming the bleed procedure:
    1. If a DTC is detected, check for the cause and repair as necessary.
    2. If the brake pedal feels spongy, perform the conventional brake bleed procedure again.

  9. When the desired pedal height is achieved, press the brake pedal in order to inspect for firmness. Remove the scan tool.
  10. Install the tire and wheel assemblies. Inspect the brake fluid level.
  11. Road test the vehicle while inspecting that the pedal remains high and firm.

  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF.
  7. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  8. Bleed the base brake system.
  9. Follow the scan tool directions until the desired brake pedal height is achieved.

Jan 03, 2011 | 1998 Chevrolet Corvette

1 Answer

No brakes on 2006 corvette


hey there
'is there any brake pads left
could need bleeding
could need a brake booster

Oct 17, 2010 | 2006 Chevrolet Corvette

2 Answers

1991 corvette brake syatem


You need to bleed this system with the special tool that holds the ABS solenoids open, it plugs into the ABS brake controller, if you don't do this there is no way to get the air out of the system, that is why your pedal is low.

Oct 29, 2008 | 1991 Chevrolet Corvette

1 Answer

How do I replace the brake power booster on a 1981 corvette


you will have to remove the master cyl no need to dissconnect the lines and dissconnect the vacuume line and from inside the car under the dash dissconnect the brake pedal from the shaft running to the booster. and remove the 4 mounting bolts that hold the booster to the firewall and pull foward in the engine compartment.
as long as you dont dissconect the brake lines you wont need to bleed the brakes.
good luck
paul

Sep 28, 2008 | 1981 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...