Question about 2000 Pontiac Grand Prix

1 Answer

How do i program the remote

How do i program the key remote

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Pontiac Master
  • 3,854 Answers

IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be useing on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.


1. Remove the key from the ignition.


2. Close all doors.


3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.


4. Insert the key into the ignition, and turn to the ACC position.


5. Turn the key to OFF and then back to ACC within 1 second.


6. Open and close any vehicle door. A chime will be heard when the system enters into programming mode.


7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.

IMPORTANT: After 7 seconds, a chime may be heard confirming successful
synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


8. Repeat step 7 now for each additional remotes to be programmed including any existing remotes.


9. Remove key from ignition.


10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).


Thank you for using fixya and good luck

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Resync polo key 2000 how do ido it i have spare key


Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Mar 18, 2017 | Volkswagen Polo Cars & Trucks

1 Answer

Programming key fobs for a 2007 Silverado


If Your 2007-2010 Silverado Has a VIC - Vehicle Information Center Step 1: Sit in the vehicle with all the doors closed and unlocked. Start your Silverado and leave it in Park.
Step 2: Press and hold the Vehicle Information button, marked by an image of a car and the letter "i", until the display reads "Press V to Relearn Remote Key".
Step 3: Press the Set/Reset button until "Remote Key Learning Active" appears.
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).
If Your 2007-2010 Silverado Doesn't Have a VIC - Vehicle Information System Step 1: Sit in the vehicle with all the doors closed and unlocked. Turn the key to Accessory Power position.
Step 2: Press the trip odometer meter reset stem repeatedly until you see "Relearn Remote Key".
Step 3: Press and hold the trip odometer meter stem for three seconds. The display will read "Key Learning Active".
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).

Nov 02, 2016 | Chevrolet Silverado Cars & Trucks

3 Answers

MY PT Cruiser Functional transmitter and the one to be programmed both have no "PANIC" Button . How I programme the spare Fob


If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Sep 05, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Where is the re-set button to program a remote door lock for my 2000 Subaru Forester?


Obtain all keys/remote controls. Remove driver's side kick panel/lower 'A' pillar trim. Connect central locking registration connectors (white) - black wire and black/blue wire Fig. 2 . Unlock the vehicle using the key. Program first key/remote control as follows: Press unlock button Fig. 1 [1], then lock button [2]. The door lock should lock and unlock in sequence confirming programming of first key/remote control. Repeat programming procedure for remaining key(s)/remote control(s). Once the last key/remote control is programmed disconnect central locking registration connectors. Check operation of all programmed keys/remote controls.

Sep 03, 2010 | 2000 Subaru Forester

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

1 Answer

Replaced battery on my remote control and it does not work. does it needs to be re-programmed again?


Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons

To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).


Good luck and hope this helps, you may have to reprogram. merry Xmas


Dec 24, 2009 | 2007 Chevrolet Tahoe

1 Answer

Programing remote contr ol


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.

Jun 08, 2009 | 1999 Buick Regal

2 Answers

Lost jeep 2000 grand cherokee key and remote


go to the car dealer and tell them that you need to get a new key and remote for your car

Apr 09, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Keys won,t lock or unlock doors


Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

Mar 25, 2009 | 2005 Buick LaCrosse

1 Answer

2005 cadillac sts remote transmitter


This is the procedure for a reprogram of the remote's from the factory service manual, if it doesn't work then u may have a receiver issue.
Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).


Use this Procedure for Vehicles without
Drivers Information Center Buttons


To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).

Jan 17, 2009 | 2005 Cadillac STS

Not finding what you are looking for?
2000 Pontiac Grand Prix Logo

541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...