Question about 2001 Chevrolet Silverado 1500

1 Answer

On a 4 wheel drive is the front driveshaft suppose to turn when in 2 wheeldrive

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 289 Answers

Yes the driveshaft will turn all the time

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wheels do not engage in 2 wheeldrive and front wheels on engage in 4 wheel drive??


If driveshaft to rear end spins then you have something broken in the rear end. If the driveshaft doesn't spin then problem with transfercase.

May 31, 2015 | Cars & Trucks

1 Answer

I have a 2001 chevy s10 4x4 the fourwheel drive is lockin in but my tires are not spinning? WHAT do I do


Check if the front driveshaft is turning the front diff pinion. If it is then check the axle fork engage operation on the right side of the differential

Feb 28, 2015 | 2001 Chevrolet S-10

1 Answer

I reconnected wires and with 4 wheels off ground the driveshaft turns but 4 wheel drive on front dif still doesn't work


What kind of car or truck? If both driveshafts turn, then you have a bad front differential. Remember there are 2 driveshafts on 4 wheel drive vehicles. Also do you ahve locking hubs?

Feb 04, 2015 | Cars & Trucks

1 Answer

Why does my 4 wheel drive not work all the time?


Elaine,

not work, do tell what makes you think it dont work (a lamp) or tires slipping or dead tires. (by tires mean that and traction)??????????

what mode fails, of the many, and where.???????



first off, we dont know what your tires are touching.

on road, or off road. pavement or ICE or snow.

that matters big time . (you read manual and match MODE to Road)

your lost operators guide explains all that, right?

eg: how and when to use, 4wd, its all there. I promise.

ControlTrac 4-wheel-drive system



here are the mode. which one , gives you problems.



quote ford with comments.



What are the modes, and how do they differ?

(note this is the operational behavior of a 2008 Ford Expedition. Newer and older Expeditions will vary only slightly)



2H 2-wheel-drive with high range gearing (1.00:1) Rear-wheel-drive capability,

2-wheel electronic traction control system is enabled



4A 4-wheel-drive Auto with high range gearing (1.00:1) Full-time all-wheel-drive capability, ((best on pavement or any time)

Electronically adjusted torque split to front & rear wheels, Electronically variable center differential,

Front driveshaft & rear primary driveshaft allowed rotational speed difference,

4-wheel electronic traction control system is enabled



4H 4-wheel-drive with high range gearing (1.00:1) Part-time 4-wheel-drive capability, (not for dry pavement EVER)

Continuous 50/50 torque split to front & rear wheels, Electronically locked center differential,

Front driveshaft & rear primary driveshaft mechanically locked with no rotational speed difference,

4-wheel electronic traction control system is enabled



4L 4-wheel-drive with low range gearing (2.64:1) Part-time 4-wheel-drive capability, (off road usage, mostly)

Continuous 50/50 torque split to front & rear wheels, Electronically locked center differential,

Front driveshaft & rear primary driveshaft mechanically locked with no rotational speed difference,

4-wheel electronic traction control system is enabled, ESC and RSC are disabled



In 4A mode the center differential is electronically-controlled and rear drive wheel bias. The on-board computer monitors for any sign of rear drive wheel slip (loss of traction)

If loss of traction is detected, the center differential is told to send a share of the engine\'s torque to the front drive wheels. It will not let the front driveshaft turn at the same speed as the rear driveshaft.



What about traction management?

1997-2002 model Ford Expeditions offered an optional limited-slip rear differential (LSD). A conventional open rear differential was standard along with the conventional open front differential and the electronic locking center differential.

comment with out LSD, one tire can spin, on say ice.

but the other 3 tires dont, in full time.

Jul 04, 2014 | 2003 Ford Expedition

1 Answer

Isnt the driveshaft to the front diff supposed to freewheel when not in 4wheel drive?


it is unless hubs are defective or ingaged.Lift front end up and turn rotate wheels and se if u joint behind wheel is turning if it is you have a problem with hubs and while up in the air turn drive shaft by hand if it turns-- transfer case proubly ok go to hubs goo luck

Jul 16, 2011 | Jeep Wrangler Cars & Trucks

3 Answers

4wheel drive wont engage


First, start checking the fuses an there is also an electrial activaced switch at the transmission or transfer case that may be bad.

95-96
Your control knob should say 2wd, 4auto, 4low.

First, we need to narrow it down to a transfer case issue, or a front axle issue.
Step 1) Jack up the front end and place it securely on jack stands.
Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels may or may not turn. Do not be alarmed if they don't turn. This is normal for your vehicle.
Step 3) Start the vehicle and let it idle. Place your foot firmly on the brakes, place the transmission in NEUTRAL, engage 4low, then place the vehicle back in park. DO NOT ENGAGE ANY GEAR!! The lurch as the transmission engages could cause the vehicle to lurch and potentially fall off the jack stands.**If you can turn the front driveshaft, the transfer case is not locking. This could be due to a mechanical issue with the transfer case itself, or an electrical gremlin with the control system. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If both wheels spin in opposite directions, then the front axle *should* be properly engaged. Take it for a test drive (after safely lowering it to the ground, of course). If the front wheels do not spin in opposite directions, there is a problem with the front axle. This could be due to a mechanical problem with the diff, or a failure of the center axle disconnect to engage the passenger side axle shaft. Start a new thread with the results of your checks, and we'll go from there.

Troubleshooting the CAD on a 95-96 is a bit more involved than I want to get into here, and the problems can vary widely. This'll get you started.


97-01 4-door and 96-00 Sports
Your control knob should say 4auto, 4high, 4low.
First, we need to narrow it down to a transfer case issue, or a front axle issue.

Step 1) Jack up the front end and place it securely on jack stands.

Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels should turn. (If only one turns, don't be alarmed. One wheel sometimes has more resistance in the brakes, bearings, or CV joints. This is normal)
Step 3) Start the vehicle and let it idle in PARK. Engage 4high. DO NOT PUT THE VEHICLE IN GEAR!!! Crawl underneath and see if you can turn the front driveshaft.
**If you can turn the front driveshaft, the transfer case is not locking. This could be due to a mechanical issue with the transfer case itself, or an electrical gremlin with the control system. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If both wheels spin in opposite directions, then the front axle *should* be properly engaged. Take it for a test drive (after safely lowering it to the ground, of course). If the front wheels do not spin in opposite directions, there is a problem with the front axle. Start a new thread with the results of your checks, and we'll go from there.


'01-'03 Sport and '01-'05 Sport Trac
Your control knob should say 2wd, 4high, 4low

The transfer case in these trucks functions essentially like the 1st-gens' 13-54 t-case. (i.e. it uses a lockup collar engaged by the transfer case shift motor) The troubleshooting procedure is very similar, but you don't need to worry about hubs or center-axle disconnects engaging.

Step 1) Jack up the front end and place it securely on jack stands.
Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels should turn. (If only one turns, don't be alarmed. One wheel sometimes has more resistance in the brakes, bearings, or CV joints. This is normal)
Step 3) Start the vehicle and let it idle in PARK. Engage 4high. DO NOT PUT THE VEHICLE IN GEAR!!! Crawl underneath and see if you can turn the front driveshaft.
**If you can turn the front driveshaft, the transfer case is not locking. The shift motor could be falsely reading an incorrect t-case position, or it could be a mechanical issue with the case itself. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If it does, the system should be properly engaged. Safely lower the vehicle to the ground and take it for a test drive. If the wheels do NOT spin in opposite directions, there is a problem with the front differential or axle. Start a new thread with the results of your checks, and we'll go from there.


Keep us updated.

Dec 16, 2010 | 1996 Ford Explorer

2 Answers

Is the front driveshaft suppose to turn in 2 wheeldrive


Yes, unless you have installed lock out hubs on the truck. The shaft is being driven by the front wheels. Lock out hubs let the front wheels freewheel and save wear and tear and (maybe) a little gas.

Apr 27, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

My 1999 Blazer 4X4 will not go into 4 wheel drive.


The cv shafts will turn in 2wd but the front driveshaft should not. Can you jack up all 4 wheels to test this?

Jul 04, 2009 | 1999 Chevrolet Blazer

2 Answers

95 chevy blazer 4wheel drive problem


I now these trucks pretty well, I own 2, a 2000 two door and a 95 4 door and before them I owned a 88 and an 87, so look I suggest you use 4 hi but in low geer(1st geer) and just let it grab by itself, cause I find first thing it's hard getting into 4 low cause you must be in neutral,and I usually engage it with only the ignition on without actually running the truck to make sure it actually engages, we get a lot of snow up here so I'm letting experience speak for itself, hope it helps...

goodluck...

Dec 17, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...