Question about 2007 Toyota RAV4

1 Answer

Fan only works on high - 2007 Toyota RAV4

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Most likely the (blower motor resistor) has burnt out a few of its elemental coils....default is hi when they burn out, so you have something as apposed to no blower when it fails.

Posted on Apr 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A.c only works on high


Year/make/model??? Are you referring to the AC fan speed only working on high inside the vehicle? If the fan is only operating on the high speed, suspect a fan motor resistor problem. The resistor may have to be relaced

Jan 28, 2016 | Cars & Trucks

3 Answers

My low cool and low fan does not work. High cool and high fan works good. Is this something I can fix myself and if so, how?


If it is a Ford product the problem is with the ignition switch!!!!!!!!High cool function bypasses switch, Other speeds do not.
Your headlights might not be working either.

Jul 29, 2015 | Cars & Trucks

2 Answers

Why does heat-air fan only work on high


Can you tell that the fan is getting higher or lower? Or is there no response from the fan control until you get to the high position?

Jun 24, 2014 | 2001 Chrysler Town & Country

1 Answer

AC and Heater fan will only work on high speed, all fuses good. any ideas thanks, Dave


When the blower fan will only work on high speed setting this means the fans speed control resistor is burned out, when it fails the fan defaults to high speed only. The fan resistor is located next to the fan and held into the cooling air duct by 2 screws near the blower motor. The part is fairly cheap and easy to replace.

May 11, 2011 | 2000 Mercury Villager

1 Answer

Cool fan low doesn't work. Doesn't appear to be


It needs to have the blower motor resistor card replaced.
It still works on high speed because on the high setting the voltage does not go through the resistor.
The resistor is mounted beside the blower motor and is easy to replace.
There you are, thank you for using FixYa.

KL

May 01, 2010 | 2003 Saturn VUE

1 Answer

The only speed on my heat/air fan the will work is high. All other speed quite at the same time. Would this be the fan motor or could it be a fuse?


It is most likely the fan switch, all the low speed work through a resistance, the full speed does not, there is only one fuse for the fan so if it works on high its ok and you say the fan works on high so the fan itself is ok

Apr 17, 2010 | 2005 Ford Taurus

1 Answer

Why does my heater in my 2000 ford ranger only work on the high setting?


I assume that you are talking about the heater fan?

Your heater FAN has at least 3 settings, and for our purposes we will assume low,med and high

Low and medium run through a resistor High is wired direct
Either your resistor is bad or your fan is
I know it seems wrong that the fan could be shot but it could be pulling so many amps that it won't work in any other mode than high
I just had this happen on one of my trucks
Start with the fan

Apr 06, 2010 | 1998 Ford Ranger SuperCab

1 Answer

Heater & cooling fan only works on high.Power locks don't work.


there is a resistor for the heating and cooling fan speed. this controls the amount of voltage to your fan, which controls the speed. usually when the fan only works on high it will bypass the resistor and use the full 12 volts for the high setting. your power locks might be part of this circuit. i would check the resistor first then check the locks. usually the resistor is behind the high low switch

Mar 26, 2010 | 2000 Pontiac Montana

3 Answers

Heat/AC Blower fan speed only works on High


Alot of people have the same problem with the fan switch and blown bulbs. There really is no fix for this. Jeep really screwed up when designing the heater control assembly. The cheapest solution is to buy another unit off Ebay. Can always go to the dealer but be ready to PAY for there mistakes.

Jan 14, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2007 Toyota RAV4 Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...