Question about 1983 Dodge Ramcharger

Open Question

How do you install wheel bearings on a 1983 dodge ramcharger 4x4?

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 507 Answers

SOURCE: 98 dodge ram 1500 4x4 wheel bearing replacement

Yes those are bolts. You remove those from the back side. This takes a while sometimes. If you can't get them by reverse alone, try hitting them with impact in forward for a hit or two to brake it loose a little. If the new hub comes with new bolts, don't be afarid to brake them. PS, after those bolts are removed, don't forget to remove the nut on the axle shaft. You may also need to use an air hammer to help remove old hub after bolts are removed.

Posted on Sep 06, 2008

  • 103 Answers

SOURCE: is front drivers side wheel

depends on what you mean by "hard" if your mechanically inclined no, if you aren't, yes. You will need to remove the tire, the brake assembly and then get a large (32 or 34mm probably) socket to take off the spindle nut, I think on the dakota you have to remove the ball joint with a ball joint separator, remove the bearing assembly from the half shaft. (standard procedure on most vehicles) Hope this helps!

Posted on May 12, 2009

  • 86 Answers

SOURCE: 97 dodge wheel bearing abs &not

yea you can. but your abs light will be on and that might cause a problem when inspecion comes around. depending what state your in.

Posted on Jun 29, 2009

  • 10319 Answers

SOURCE: I have 1990 Dodge Ramcharger 318 4x4. we just

Check the shift cable attatchments for a secure fit. If loose it will not move into any other shifting range

Posted on Jan 22, 2010

  • 52 Answers

SOURCE: when you replace front wheel bearing on dodge ram

175 ft pounds for the axl nut it gona take alot to get it of.the nut size is 1 -11/16. air tools make it easy the hub to nuckle nuts are 14mm 12 point.

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Where is the vacuum shift motor located?

Gordon, I will take a guess, the Vacuum shift actuator/motor is located on the front axle. Check the attached pictures of actuator and how to replace video,links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagnosing 4WD Engagement Problems on Dodge Ram pickups
Front Drive Axle 4wd Vacuum Disconnect Motor 1AFWA00007
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram

May 18, 2016 | 1983 Dodge Ramcharger

1 Answer

Hood latch cable on a 1978 Dodge Charger broken how can I open the hood??

see if can remove grill center piece and lever the latch with screwdriver if can reach

Mar 19, 2014 | 1983 Dodge Ramcharger

1 Answer

I have a 1989 Dodge Ramcharger 318 Rear End

Did you turn the bearing adjusters on the ends? They are held still with little bolts.

Jul 09, 2010 | 1989 Dodge Ramcharger

1 Answer

Transmission leaking in the front of a 1983 dodge ramcharger

transmission line,front seal or leaky pan gasket

Apr 14, 2010 | 1983 Dodge Ramcharger

4 Answers

I have 1990 Dodge Ramcharger 318 4x4. we just

Check the shift cable attatchments for a secure fit. If loose it will not move into any other shifting range

Jan 22, 2010 | 1990 Dodge Ramcharger

1 Answer

How do you remove the rotors

not sure what your asking you want to remove your brake rotors?

Jul 02, 2009 | 1983 Dodge Pickup

1 Answer

Front wheel bearing removal on dodge Ram 4x4- 2003

Sorry this is a very difficult job and you will need special tools,take my advice and take it to your local spanner man

May 30, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Fuel system problems

Try running some fuel back through the feed line from the pump to the tank. Chances are you will see fuel leaking out of it somewhere. The pump on the engine pulls fuel. Even a pinhole will draw in air.
You did check the sock filter in the tank right?

Apr 25, 2009 | 1983 Dodge Ramcharger

1 Answer

I have to keep replacing the wheel bearings on my 2001 dodge 4x4

are you greasing them (packing) the bearings ?.... also don't over tighten the nut.... put the nut on..... spin the wheel and tighten the nut just enough to allow it to spin


Jan 01, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

1990 Dodge 250 2wd trans fit 4x4 1988 Ramcharger

if you are talking about the trans no! the 2wd trans has a longer output shaft than the 4x4 you can have the shaft changed so that it can work if you are having trouble finding a trans.

Dec 30, 2008 | 1988 Dodge Ramcharger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides