Question about 1995 Lincoln Continental

1 Answer

How do I replace the center mounted brake light located on back window shelf?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 267 Answers

Usually you gain access thru the trunk llok for wire connection and bolts that hold it in place

Posted on Apr 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace third mount break light 2010 Chevy Malibu lt


Remove the rear window package shelf. Disengage the rear window shelf insulator from the rear shelf trim panel in order to get to the high mount stop lamp screws. Disconnect plug.

Oct 14, 2016 | 2010 Chevrolet Malibu

2 Answers

How do I replace the high mount brake light on my 2011 Chevy Malibu?


You need to take the back seat out. Remove the C-Pillar trim panels. Lift up on the package shelf. Unplug the wiring connector. I've had mine out when I changed the speakers.

BTW, Its Not a Bulb. Its a LED Assembly. Replaced as a whole unit. Unless your good with electronics and soldering.

Jul 16, 2015 | 2011 Chevrolet Malibu

1 Answer

How to replace the third brake light bulb on 2005 ford five hundred


9_5_2012_9_14_11_pm.gif

  1. Remove the parcel shelf.
  2. Remove the 4 high mounted stoplamp mounting screws.
  3. Remove the high mounted stoplamp.
  4. To install, reverse the removal procedure.
Parcel Shelf Removal and Installation


9_5_2012_9_15_32_pm.gif

Sep 05, 2012 | Ford Five Hundred Cars & Trucks

2 Answers

WHAT IS THE THIRD STOP LIGHT


The third brake light is the brake light in the center of the vehicle either around the lower part of the rear window or above the rear window. They didn't start to become common until the late 80’s - early 90's. It is also known as the high mount brake light or the cyclops break light? If that's not what you where looking for let me know and I'll be happy to help you further. Thank you for using fixya.com

Oct 16, 2011 | Cars & Trucks

1 Answer

1999 Chrysler Concorde LXI Rear Speaker replacement


If you mean the rear shelf removal, then you begin by removing the rear seat (lift to release the corner clips on each side holding the cushion to the floor). Then remove the fasteners for the seat belts, then lift the seat back to raise and release it from its clips, and remove it from the vehicle. There are then a lower and upper trim panel around the back shelf that you need to remove (these may be on each side of the shelf, e.g. they are called 'quarter trim' panels). Then you will see some push-pin fasteners that hold the shelf across the front lower edge, so you gently pry out the center push-pin of each one of those to release the fastener. Then you pull the shelf forward to release it from the clips that hold it under the window. Then remove the wire to the center high-mounted brake light. The panel with its speakers attached can then be removed, but also remove the wires from the speakers so you don't break those. connections.
That is the procedure as shown in my '98 manual.

Mar 31, 2010 | 1999 Chrysler Concorde

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

How do I replace the brake light in the upper back window


Please don't forget to rate! Thank you....
High-Mount Brake Light
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens.

9230a99.gif
  1. Installation is the reverse to install. Connect the negative battery cable, then check the lamp for proper operation.

Mar 06, 2010 | 1996 Pontiac Grand Am

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

1 Answer

Were is the rpo relay located . my regular brake light don't turn on. i check light bulb r ok. there is no power to going to the back lights


RPO relay?? no power to rear lights or just brake lights?? is there power at the brake light switch? does the center high mounted brake light work? if the center light works the the switch is good. fuse #13 powers the brake lights (all)

Sep 28, 2009 | 2000 Ford Expedition

1 Answer

Hight mount brake light


hi im thomas

if you mean the parshell shelf brake light the you will need to open the boot lid, there will be carpet on the bottom of the parshell shelf top of the boot behind the seats there will be about 6 to 7 clips you will need a flat blade screw driver and 1 smallpair of pointy nosed plyers to remove them the piece of carpet should come down your globe will be in there

Jul 16, 2008 | 1999 Nissan Altima

Not finding what you are looking for?
1995 Lincoln Continental Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...