Question about 2004 Volkswagen Beetle

1 Answer

Where is the (transmission control module) and (speed sensor input) located at, on a 2004 VW new beatle,2.0L.,no turbo?

Posted by on

  • samsoncrabtr Apr 27, 2010

    theres nothing posted for my question

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Output and input speed sensors are located inside transmission below valve body.

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Malibu error codes po700,po716,po717


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination

Which one of these transmissions does your Malibu have ?
Automatic Transmission - 4T45-E
Automatic Transmission - 6T40/6T45
Automatic Transmission - 6T70/6T75

Do you know how to find out look at the VIN # ?
DTC P0716: Input Speed Sensor Performance
DTC P0717: Input Speed Sensor Circuit Low Voltage
The automatic transmission input speed sensor (ISS) is a permanent magnet with a coil of wire wound around. The ISS mounts in the case cover facing the reluctor wheel of the input shaft. As the reluctor wheel is driven by the turbine shaft, an AC signal is induced in the input speed sensor. Higher vehicle speeds induce a higher frequency and voltage at the sensor. There is a fixed air gap between the sensor and the teeth on the sensor reluctor wheel. The ISS input is used by the transmission control module (TCM) in order to control line pressure, torque converter clutch (TCC) apply and release, and transmission shift patterns. This sensor is also used to calculate the appropriate gear ratios and TCC slippage. This diagnostic indicates stuck, erratic, or intermittent conditions in the system.
Diagnostic Aids
• Road test the vehicle while monitoring the Transmission ISS parameter on the scan tool. The Transmission ISS parameter should vary with engine speed changes and not abruptly drop out.
• Inspect for an open or shorted AT ISS wire.
• Inspect for a disconnected AT ISS connector.
• Inspect for a faulty AT ISS.

Trouble Code P0717 Input speed sensor

Jan 19, 2017 | Cars & Trucks

1 Answer

Where is the input turbo speed sensor located for my 2004 Chevy Cavalier? Is inside the transmission?


The input would be on the front wheels .The out put is on the output of the transmission .So the input from the wheels turning is sent to the pcm and compared with the out put of the transmission out put shaft that puts the drive force to the road .
It could be reversed from front to rear but the concept is the same the computer senses the free wheel spin rate and then adjusts controls like fuel trim and timing air intake and so on compared to the speed of the transmission shaft
Hope this helps

Sep 09, 2016 | 2004 Chevrolet Cavalier

1 Answer

Location of speed sensor


Vehicle Speed Sensor Removal & Installation - YouTube

? 8:47
www.youtube.com/watch?v=rAenb7qb3BY
Jul 4, 2012 - Uploaded by TheYoshiClan Speed Sensor Replacment Fix Transmission Shifting Problems ...10 Min Automatic Transmission Fluid Flush + Replacement (Most

Sep 16, 2015 | 2004 Ford F350

1 Answer

I am looking for a ECU pinout or a Diagram. I am throwing a "turbine overspeed" code (P0716) on a non turbo car. Also P0721 and P0705 On second ECU with the same issue.


Hello. You are confusing the turbine over speed control sensor module of the car's transmission, with a turbo charger- a forced air induction device, of a car's engine. One has nothing to do with the other.

The turbine over-speed control module is basically a sensor that reads the speed of the transmission's input shaft (torque converter) in relation to the speed of the output shaft- transmission speed ratio/gear.

Simply put- when the P0716 error code displays, it means that the ECM has detected the value(s) of the input sensor as being out of range, like being too high or too low; or that there is some bad wiring issue in the circuit.

When this happens, the subsequent P0721 output speed sensor and P0705 transmission range sensor circuit malfunction error codes appear- and does not necessarily mean that the entire transmission components (electronic modules, sensors, or mechanical parts) have malfunctioned leading to a major transmission overhaul.

It is most likely that the Input Turbine Speed sensor needs to be replaced. Take the car to a well qualified SAE certified transmission specialist who has precise diagnostic and transmission control readers and are able to reset the computerized transmission modules once the repair is made.

Feb 20, 2015 | 2006 Kia Sorento

1 Answer

Where is the vw passat 1.9tdi traction control sensor.


it is part of the power train control module (PCM) and takes part of it's input from the wheel speed sensors located in each hub as well as the vehicle speed sensor located in the transmission

Feb 11, 2015 | Cars & Trucks

3 Answers

Automatic transmission input shaft speed sensor


(440) Automatic Transmission Input Shaft Speed (A/T ISS) Sensor Assembly

6ff31511-ab33-4aa1-8564-0dedbca55053.jpg

Jul 02, 2014 | 2004 Chevrolet Impala

1 Answer

1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problems

Possible causes
- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor

Hope this clues helps to solve it.

Jun 02, 2011 | 2003 Chrysler Sebring

2 Answers

Where is the speedometer relay in a 1996 chevrolet van?


There is no speedometer relay. The speedometer input is provided from the vehicle speed sensor that is located in the tailshaft portion of the transmission.
This input is also used by the power train control module (or PCM) and is used as an input for transmission shifting.

Mar 31, 2010 | 1997 Chevrolet Astro

1 Answer

1998 dodge avenger tranmission control solenoid


Below the link for Chrysler/Dodge auto-transmission manual
http://www.scribd.com/doc/7095618/545rfe-Transmission-Manual

Solenoid mounts outside the transmission, so you do not need to remove the transmission to install. It should be located between fuse box and air filter housing on the top of transaxle case and right next to transmission controle module.
I hope his step by step procedure will work for you. It is not hard at all to replace the solenoid. There are three 10mm bolts. You will also need to remove the input speed sensor. One thing to look out for is not bending the gasket when installing the new solenoid:
  1. Disconnect battery negative cable.
  2. Remove air cleaner assembly.
  3. Remove electrical connectors for transmission control module (please refer the manual I send you and autozone.com website).
  4. Remove the Transmission Control Module
  5. Disconnect and remove the input speed sensor
  6. Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
  7. Disconnect the solenoid/pressure switch assembly connector.
  8. Remove the three solenoid/pressure switch assembly-to-transaxle case bolts
  9. Remove solenoid/pressure switch assembly and gasket

Keep everything clean to prevent foreign materials to go inside
  1. Install solenoid/pressure switch assembly to case using a new gasket
  2. Install bolts and torque to 13 N·m (110 in. lbs.)
  3. Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
  4. Uncap and install transmission oil cooler lines.
  5. Install input speed sensor and torque to 27 N·m (20 ft. lbs.)
  6. Install Transmission Control Module
  7. Install air cleaner assembly.
  8. Connect battery negative cable.

P.s. 1. You can fine some clips on YouTube.com at least for similar cars
2. Also at Autozone.com you can find the component location for your car and repair guide
3. Also there is a link for Mitchel1 online manual useb by US mechanic 1 week subscribtion is
11.99 , 1 month 16.99
http://www.2carpros.com/kpages/auto_repair_manuals.htm
Let me know if you need more info
Good Luck and happy fixing

Jan 22, 2009 | 1998 Dodge Avenger

4 Answers

I have a code p0715, which is the input turbine speed sensor


The input/turbine speed sensor has nothing to do with the turbo. It is transmission related and is a circuit malfunction. I am having the same problem and it causes my car to downshift into 3rd gear (computer's fail safe gear) on the highway. The sensor is located above the transmission housing, and doesn't require you to take apart the tranny. I am having trouble finding the part number for this and where to buy it. Any help would be nice.

Dec 26, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

1,092 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...