Question about 2000 Toyota Land Cruiser

Open Question

Replace front wheel bearings

Cannot figure out how to remove the front rotor and then replace front wheel bearings

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad
  • 373 Answers

SOURCE: wheel bearing

HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Posted on Jul 04, 2008

SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job: http://www.toyotanation.com/forum/showthread.php?s=714b28cb1c3f77f992209de0bdbfbd13&p=2481776#post2481776

Posted on Sep 23, 2008

  • 19 Answers

SOURCE: Replacing front wheel bearing

The brake rotor needs to be removed, drive shaft nut in center of hub then 3 bolts hold the hub assembly to spindle from back side. if it has abs unplug it then some work will need to be done with a hammer and chisel to work the bearing out of spindle and axle shaft from bearing

Posted on Oct 16, 2008

  • 132 Answers

SOURCE: Hyundai excel x3 front wheel

soak good with wd40 first then use a short piece of wood and a hammer to belt them off careful not to hit the axle with the hammer hope this helps glenn..........

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

1 Answer

How do you replace a front wheel bearing


remove the wheel, remove the spindle dust cover and remove tho cotter pin and remove brake caliper and finally remove thr spindle nut,washer and inner bearing and finally the rotor. remove the dudt seal on the back of the rotor and finally the inner braeings.when you replace the bearings make sure that you replace the races and install a new seal on the rotor

Sep 03, 2014 | 1993 Ford Crown Victoria

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

I've changed rotors before but never on a 4 wheel drive. Could you tell me how to on a 1989 ford ranger?


Brake Rotor (Disc) - REMOVAL & INSTALLATION
  1. Loosen the wheel lug nuts.
  2. Jack up the front of the vehicle and support on jackstands.
  3. Remove the wheel and tire.
  4. Remove the brake caliper assembly as described earlier in this section, but do not disconnect the brake hose.
  5. Suspend the caliper assembly by a piece of wire. Do not allow it to hang by the brake hose.
  6. Follow the procedure given under wheel bearing removal in Suspension and Steering for models with manual and automatic locking hubs (lines down).
New rotor assemblies come protected with an anti-rust coating which should be removed with denatured alcohol or degreaser. New hubs must be packed with EP wheel bearing grease.
  1. Installation is the reverse of the removal procedure.


Front Wheel Bearings - REMOVAL & INSTALLATION
(see Figure 1 )


zjlimited_533.gif

Fig. 1: Inspect the bearings for abnormal wear and/or damage



With Manual Locking Hubs
(see Figures 2 through 17)

  1. Raise the vehicle and install jackstands.
  2. Remove the wheel and tire assembly.
  3. Remove the retainer washers from the lug nut studs and remove the manual locking hub assembly from the spindle.
  4. Remove the snapring and spacer from the end of the spindle shaft.
  5. Remove the outer wheel bearing locknut from the spindle using 4 prong spindle nut spanner wrench, T86T-1197-A or equivalent. Make sure the tabs on the tool engage the slots in the locknut.
  6. Remove the locknut washer from the spindle.
  7. Remove the inner wheel bearing locknut from the spindle using 4 prong spindle nut spanner wrench, T86T-1197-A or equivalent. Make sure the tabs on the tool engage the slots in the locknut.
  8. Remove the outer bearing cone and roller assembly from the hub. Remove the hub and rotor from the spindle.
  9. Using seal removal tool 1175-AC or equivalent remove and discard the grease seal. Remove the inner bearing cone and roller assembly from the hub.
  10. Clean the inner and outer bearing assemblies in solvent. Inspect the bearings and the cones for wear and damage. Replace defective parts, as required.
  11. If the cups are worn or damaged, remove them with front hub remover tool T81P-1104-C and tool T77F-1102-A or equivalent.
  12. Wipe the old grease from the spindle. Check the spindle for excessive wear or damage. Replace defective parts, as required.
zjlimited_534.gif

Fig. 2: Before beginning the wheel bearing removal, and after the outer hub is removed, wipe off any excess grease

zjlimited_535.gif

Fig. 3: After the grease is wiped off, remove the axle shaft snapring ...

zjlimited_536.gif

Fig. 4: ... then pull the splined spacer from the axle shaft end

zjlimited_537.gif

Fig. 5: Use a 4 pronged socket to loosen the outer wheel bearing locknut ...

zjlimited_538.gif

Fig. 6: ... then remove the outer locknut

zjlimited_539.gif

Fig. 7: Remove the lockwasher from behind the outer locknut ...

zjlimited_540.gif

Fig. 8: ... then loosen and remove the inner locknut-note the lockwasher engagement pin (arrow)

zjlimited_541.gif

Fig. 9: While pushing inwards on the rotor/hub assembly, remove the outer wheel bearing ...

zjlimited_542.gif

Fig. 10: ... then pull the rotor/hub assembly from the spindle, taking care not to scratch the bearing cups in the hub

zjlimited_543.gif

Fig. 11: Pry out the grease seal on the back of the rotor/hub assembly ...

zjlimited_544.gif

Fig. 12: ... then remove the inner wheel bearing. Thoroughly clean and inspect all of the parts for wear or damage





continue...

Jul 29, 2011 | 1989 Ford Ranger

3 Answers

WHy dose my brake pedal push back and make a grinding noise


Look through the openings in your front wheels and look at the front rotors-are they gouged up? You are probably running metal-to-metal, pads to rotors.
Chances are real good your rotors will have to be replaced along with new pads, but if you catch it early enough you might be able to have them machined, although nowadays that is hardly easy to get done and the savings usually is not as significant as it once was.

May 23, 2011 | 1995 Pontiac Bonneville

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

1 Answer

Replacing front rotors


you do have to dissasemble the hubs because the rotors bolt on to them. if it is two wheel drive take the center caps off of hubs remove the spindle nuts and bearings pull complete hub assembly off and unbolt rotor from hub. if it is four wheel drive you will have to remove the lockout assembly be careful not to loose any parts from this it won't work when put back together.

Aug 26, 2009 | 2001 Isuzu Rodeo

1 Answer

I just tried to replace the front rotors on my 1996 nissian pathfinder, but couldn't figure out how to remove the wheel bearing (or is it the hub?). What do I have to do get the rotor off?


- disconnect ABS sensor and move away to protect from damage
- remove brake caliper assy.
- remove hub cap
- remove snap ring w/tool
- remove lock washer
- remove wheel bearing lock nut (tool J36001)
- pull off wheel hub & wheel bearing (do not drop it!)
- rotor is attached to hub.

Apr 28, 2009 | 1996 Nissan Pathfinder

Not finding what you are looking for?
2000 Toyota Land Cruiser Logo

Related Topics:

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...