Question about 2005 Chevrolet Malibu

1 Answer

Skipping after even after replacement of EGR Valve

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

How are the spark plugs? did you replace those? how many miles in the car?
how is the air filter? is it clean? is there any obstruction in the air ducts?

Posted on Apr 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 ord skipping on ever outher sinler


apparently the EGR valve gets carbon in ti and causes all kinds of stumbling, bucking multiple cylinder misfiring. The fix is simple remove EGR valve and install 3/4" fender washer with an 1/8" hole in it from a local hardware store about 15 cents with an EGR gasket on both sides and then reinstall EGR valve and it will still function normally and cure the stumble

Aug 06, 2014 | 1991 Ford F150

1 Answer

Skipping upon accelaration 1399,1456 and 401 codes showed up


oh yes i know its you EGR valve (Exhaust Gas Recalculation)

A code P0401 most likely means one or more of the following has happened: The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced There is a blockage in the EGR (tube), most likely carbon buildup The EGR valve is faulty The EGR valve may not be opening due to a lack of vaccuum Possible Solutions In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit. Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open Clean out the EGR valve and/or tubing to remove deposits Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model) Replace the DPFE sensor (with a good quality / OEM one) Replace the EGR valve Related EGR Articles: P0400 - P0402 - P0403 - EGR System Explained

Read more at: http://www.obd-codes.com/p0401
Copyright OBD-Codes.com

Oct 02, 2013 | Cars & Trucks

1 Answer

I have a 1995 lincoln towncar. It runs great until it warms up it. Then it starts to sputter and stall, I have done plugs wires and coil packs to fix a skip in the motor. That worked, now I have the new...


Try replacing your Idle Air Control valve. I am a former Ford tech and have two LTC's a 94 and a 96. I have had to do this job on both. When they get up in miles, the IAC valve gets carboned up and can't adjust the air/fuel intake mixture under load. If you still have a stalling issue after that, then you will probably have to replace the EGR valve as well. But it is very important that you start the engine with the old EGR valve removed so you can blow any carbon balls out of the EGR passage before installing the new EGR valve. Otherwise you will just end up plugging and ruining the new EGR valve and have the same stalling issue. Good luck!

Mar 12, 2012 | 1995 Lincoln Town Car

1 Answer

97 ford expedition cutting off at idle . it was skipping and hesitating under strain . had it checked by a computer and it said egr valve and number 6 cylinder misfire . i changed egr valve , plugs, wires...


pull wire off # 2 see if idle changes if not there s no spark... test coil....test all vacuum lines for leaks also. if all good then idle speed sensor.

Mar 20, 2011 | 1997 Ford Expedition

1 Answer

2002 Ford Windstar p0300 skips and backfires under load


Just put a coil on a 2002 today. Coils fail a lot with no codes given

Mar 09, 2010 | 2002 Ford Windstar Cargo

1 Answer

Engine skips


That sounds like a dirty EGR valve...I had the same problem. Change the EGR valve and your problems shall be gone.

Jan 12, 2010 | 1995 Cadillac DeVille

1 Answer

98 expedition with 5.4 skipping under load


you need to get a DPFE sensor from the dealer also replace the hoses that plug in to it we always replace the EGR controler as well but thats just so we dont see the car or truck back for that problem agin

Jul 14, 2009 | 1998 Ford Expedition

2 Answers

Jumping and skipping, feels like the car might just die


That is an EGR code, replace the EGR valve and it should run fine again.

Apr 27, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
2005 Chevrolet Malibu Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...