Question about 1998 Oldsmobile Intrigue

1 Answer

How hard is it to change starter and what tools will i need?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

Not very difficult. Usually just a few sockets/wrenches and thats about it. Unbolt wires from starter and unbolt starter installation is reverse of removal. If you have any questions let me know. Also always make sure to disconnect the battery FIRST.
Thank you,

Posted on Apr 27, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How hard is it to change starter on Mitsubishi delcia

You have the tools? do it. Mitsubishi's aren't hard. I don't have a manual to tell you how. IMHO Fords are the worst. Well second if you happen to work on buses and semi's.

Sep 05, 2016 | Mitsubishi Cars & Trucks

1 Answer

2006 Buick Terraza won't start changed battery still just clicks?

It may be the starter or wires to it . Jack the car up so you can hit the starter with a hammer or tire tool .have someone hold the key in the start position and hit the starter solid but not to hard. If it turns over or starts your starter is bad. If not look at the wires for damage. Hope this helps.

Dec 14, 2013 | Cars & Trucks

1 Answer

Change starter on 2004 bmw545i

if i am not mistaking its on the top if the transmission near the fire wall. need a special tool to open the bolts. kinda hard.

Dec 02, 2012 | Cars & Trucks

1 Answer

How hard is it to change the starter? Can it be done with standard tools and one the ground without ramps? Thanks.

Since the motor is located at a lower point in the engine it will require that you JACK up the vehicle so that you can access the starter motor. It is important that you must be able to work in such postion with the tools to remove the two bolts that are bolted on the starter. You will need socket spanners/ box tools to remove the bolts.

Jul 08, 2011 | 1994 Nissan Pickup

1 Answer

How do I change the starter in a 2000 Toyota Camry LE

i'm sure it's not the starter itself that is the problem, have the stater's solenoid might be stucked. It's quite a lot of work removing the starter but you can do it if you are willing enough to learn. You just need the right idea and tools to do it. Hope this will help save you bucks!

Aug 10, 2009 | 2000 Toyota Camry

2 Answers

Can you tell me how to change the starter in an f150 1997 4 wheel drive truck I've cleaned the battery terminals and the starter wire ends from bottom of truck to the the starter. I have a new battery. I...

no special tools needed use a 1/2 inch or a 9/16 wrench for bolts but rule # 1 before you work on any electrical parts on your truck is to disconnect the negative terminal on the battery then take the starter off you 2 blots holding the starter to the engine take them off they maybe a little tight you my have use a little muscle once you take them out pull out the starter then you have to unscrew the cables use the same procedure to install I hope this information is of use GOOD LUCK

Jul 27, 2009 | 1985 Ford F150

1 Answer

Hard or no start. convinced it's the starter.

check your conections on the battery if they are carroded then you need to clean them if they are not tight that could be a problem also.if that doesn't work make sure all cannections to starter and selanoid are tight and clean if that doesn't work then more than likely it is your starter but i have never changed a starter on that type of car but most are not to hard a couple of bolts but can't be for sure on how hard it would be.

Apr 19, 2009 | 2004 Chevrolet Malibu Maxx

1 Answer

Want to know how hard it is to change the starter

its a *****. i am a mechanic and i have one of these and the starter is protected by a cover plate that requires a little more work than a normal starter but it depends on how much ability and tools you have. there are some torx drivers you will need.

Mar 31, 2009 | 1998 Land Rover Discovery

1 Answer

How do i change the starter on a 1999 sr5 4runner

You'll need basic hand tools to change out the starter. The starter is usually held in place by 2 or 3 bolts. You'll need to make sure you note where the electrical connections go in order to replace them in the correct location following starter replacement. You'll have to get under the vehicle to replace the starter, even so, It shouldn't take more than an hour.

Feb 22, 2009 | 1997 Toyota 4Runner

1 Answer

Changing a starter

its not to hard to change disconnect battery .remove nut on front of starter to support bracket . remove 2 bolts going through starter into block. lower starter . disconnect wires on solonoid . remeber where they go. tools you will need 10mm 13mm 15mm sockets

Oct 22, 2008 | 1995 GMC Sierra

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides