Question about 2005 Pontiac Sunfire

Open Question

Need torque values for disc brake caliper bolts

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 49 Answers

SOURCE: 2005 Grand Caravan Brake Job

Better late than never, right?
According to Haynes 30013: "Dodge Carvan, Chrysler Voyager & Town and Country, 2003 through 2006" Repair Manual:
Caliper Guide Pins or Guide Pin Bolts - 26 Ft-lbs

Posted on Jan 24, 2009

  • 6982 Answers

SOURCE: Front caliper securing bolts torque

I know that it's a jag, and I know you are trying to be perfect, but in over thirty years, I've never seen a tech put a torque wrench on a caliper bolt. If you really want to I'd use about 35-40 foot pounds. (I go by bolt diameter) You don't have to slam them down but you don't want them to back out either. A bit over 35 is reasonable and should not damage anything and will keep them secure!
I have no idea what nm conversion is..

Posted on Apr 09, 2009

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

emissionwiz
  • 75108 Answers

SOURCE: how to remove front rotors on 2005 nissan quest

you need to remove the caliper mounting bracket assembly and then the rotors just slide off, go to link for pictures.
http://www.2carpros.com/how_to/how_to_replace_brakes.htm

Posted on Oct 02, 2009

  • 335 Answers

SOURCE: need torque specs for brake caliper bracket bolts.

Hello and welcome. here is the torque specs for the bolts.

Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
caliper brake bracket bolts torque to 180 n.m or 133 ft.lbs

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

How do you change front brake pads on an Audi A6 2006


How to change front brake pads & rotors (brake disc) on 2006 Audi A6:

Atention!!!
Don't disconnect any brake line from caliper!
Don't disconnect any ABS sensor!
For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:

1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Remove brake carrier from wheel bearing housing (two ribbed bolts). 125 Nm
7. Remove brake disc from wheel hub.
8. Install brake carrier on wheel bearing housing. Tightening torque for two ribbed bolts = 125 Nm.
9. Check up the brake fluid level on the reservor, and emptying if neccessary!
10. Push piston back into brake caliper housing.
11. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
12. Install outer brake pad into brake carrier.
13. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
14. Install both caps.
15. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Nov 26, 2010 | 2006 Audi A6

1 Answer

Need torque specs for brake caliper bracket bolts.2000 grand prix


Hello and welcome. here is the torque specs for the bolts.

Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
caliper brake bracket bolts torque to 180 n.m or 133 ft.lbs

Jul 26, 2010 | 2000 Pontiac Grand Prix

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    1 Answer

    Torque value on 2500 front brakes


    Front caliper mounting bolts 24 ft/lb. support plate 43 ft./lb. hd front caliper adapter bolts 210 ft./lb. ld front adapter bolts 130 ft./lb. caliper banjo bolts 30 ft./lb.

    Apr 01, 2010 | 2001 Dodge Ram 2500 Truck

    1 Answer

    Torque for pyutting new rear brakes and rotors on a 2006 Town&Cou


    Caliper mounting bracket bolts 125 ft, Caliper guide pins/bolts 26 ft, Brake hose to caliper 35 ft. Wheel lug nuts 100 ft. Wheel speed sensor 115in lbs*** This is for disc rear brakes Teves system. You do know that the rear disc is a Rotor/Drum. The parking brake shoes ride on the inside.

    Jan 22, 2010 | 2006 Chrysler Town & Country

    1 Answer

    How do i get the calapers off the rear of a 2006 grand caravane?


    Using a C clamp depress the claiper. There a spot right in the middle to do this. Now the fun part hope you have metic hex key set. The 2 caliper guide pins are on the back inside the boots. Which need to be in great condition. Using the metic hex keys some are 7mm or 8mm turn to your right to remove. Rmove the caliper mounting bracket bolts. Fun part #2 removing the disc rotor. Theres parking brake pads or a durm brake system on the inside of the rotor. If the rotor does not slide off. You must remove the rubber gromet on the back of the backing plate. Using a screwdriver or the old brake adjuster tool turn the star wheel to adjust the parking brake in to remove the disc rotor. All brake guides on the calipers & guide pins need to have high temperture brake grease applyed to them. Buy the big bottle for $10 for the front brakes & future use it comes with a bush. Note ** Remove a guide pin take to auto store buy socket to reinstall guide pin/bolt. Why Caliper guide pins 26lbs torque. Caliper mounting bolts 125lb torque

    Dec 05, 2009 | 2006 Dodge Grand Caravan

    1 Answer

    Replacing my rear brake pads & discs


    1. Disconnect flexible hose. Remove the union bolt and gasket from the caliper, then disconnect the flexible hose from the caliper. Use a container to catch brake fluid as it drains out. Torque: 30 Nm (22 ft. lbs.) HINT: At the time of installation, please refer to the following item. Install the flexible hose lock securely in the lock hole in the caliper.
    2. Remove caliper.
      1. Hold the sliding pin and loosen the 2 installation bolts. Torque: 26 Nm (20 ft. lbs.)
      2. Remove the 2 installation bolts.
      3. Remove the caliper from the torque plate.
    1. Remove 2 brake pads with anti-squeal shims.
    2. Remove 4 pad support plates.
    INSTALLATION
    Installation is in the reverse order of removal.
    1. After installation, fill brake reservoir with brake fluid and bleed brake system.
    2. Check for leaks.

    Jan 13, 2009 | 1997 Toyota Land Cruiser

    Not finding what you are looking for?
    2005 Pontiac Sunfire Logo

    Related Topics:

    99 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7768 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...