Question about 2003 Pontiac Grand Am

1 Answer

How do i replace bulbs on interment panel - 2003 Pontiac Grand Am

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 57 Answers

You must take dash apart around steering column and then you should be able to pull out and unplug the gauge cluster and then unscrew back panel and you will see the little bulbs. be careful when you are taking dash apart many times they will be held together with torx bit head screws and clips sometimes + Philips head screws.

Posted on Apr 27, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace 2005 Buick Rendevous panel bulbs in ac/heat panel

You will need to remove the panel and also may need to remove its back cover to find them. Some of these bulbs are replaceable twist-in mini-bulbs (replacements can be hard to find - an AC Delco dealer/repair shop may help), but some are soldered in. GM has a bad habit of only saying "replace the panel" since they will not bother with replacing the bulbs.

Jan 08, 2017 | Buick Cars & Trucks

1 Answer

I have a 1990 GTA and have a bulb in my interment cluster behind my speedometer that will not light up. I have changed the bulb and nothing. all other bulbs in the cluster work fine any thoughts?

you have to have a bad connection between the bulb and that plastic circuit board ,. Try to bend the tabs a little or you may be stuck wiring one working bulb to another "Dashlight" working bulb... I only recommend this as a last resort because finding another cluster will not be cheap... Just a thought..

Oct 23, 2016 | Cars & Trucks

1 Answer

How to remove/replace bulb on heater control panel

rubber tubes are used to pull bulbs forward out of sockets
Bulb puller
That is if they remove from the sockets foward.
Its a gentle procedure rubber tube slightly smaller than bulb.....

Dec 06, 2013 | Cars & Trucks

1 Answer

How to replace fog bulb on santa fe 2013

"Replacing fog light bulbs on 2013 Santa Fe". Raise vehicle if you are a big person. In front of front wheels triangular plastic panels exists. Remove Phillips head plastic screws in chosen panel (2ea). Pull panel down. Stick hand through opening, remove wiring connector from bulb. (Bulb will not come out unless you do). Twist bulb housing counterclockwise and remove. Install new bulb, reverse procedure and don't touch the glass part of the bulb.

Nov 20, 2012 | Hyundai Cars & Trucks

2 Answers

I have a 99 gmc yukon my break lights stop working i changed the break switch checked the fuses and bulbs

These have the circuit board which the bulbs plug into. Very common problem for the circuit board to burn up interally and cause the brake bulbs to not work.

May 18, 2010 | 1999 GMC Yukon

1 Answer

Replace bulb

Take the back panel off of the side that the light is out on.there should be plastic bolts that hold it on. once you remove the back panel you can get to the bulb. turn the bulb housing and replace bulb. Put back the panel and you are done.

Dec 09, 2008 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Door Panel Remove 2008 Z-06

they are just clipped in, simply pull gently on one of the panel, and you will feel it pop out, you may have a screw or two to remove in the arm rest area.....

Nov 26, 2008 | 1999 Chevrolet Corvette

1 Answer

How replace break light bulb in on a4 2005

Replacement of any bulb in the Tail-light assembly is easier then one thinks.

First thing you need to do is gain access to the trunk area. At the top of
the tail-light area inside the trunk is a small circle that needs to be
opened to expose the bolt that you need to remove.

WARNING: Be careful not to loose this bolt or you are going to have to take
apart your trunk interior to retrieve it.

After the bolt is removed the Tail-light assembly will pull out as follows;
Left side: pull out the right side of the assembly
Right side: pull out the left side of the assembly.
The out side of the assembly is held in place by 2 or 3 small nipples.

There will only be one cable that is connected to the assembly. This does not
have to be removed unless you really want to. On both sides of the assembly
there are 2 clips that hold the light plate to the break light lens. After
the clips are loosened the whole light bulb assembly can be removed and the
bulbs replaced.

Restoring the Break-light assembly.

After you have replaced your bulbs and re attached the the bulb assembly, you
will have to first fit the nipples on the outer side of the assembly then
push the inter side into place. Replace the bolt and tighten. You are done.

Jul 14, 2008 | 2005 Audi A4

Not finding what you are looking for?
2003 Pontiac Grand Am Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides