Question about 1994 Mazda 626

1 Answer

Repairing of a 94 mazda,location of a Harmonic BalNCER


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 427 Answers

The lowest pulley that a belt goes around is the harmonic balancer.

Posted on Apr 27, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I fix...? how do I install crankshaft sensor for Mazda familiar zl engine please help

Mazda familiar is a ford mazda clone
hard to find the exact CAS you require online

in short ...its close to the harmonic balancer


Jun 28, 2016 | Mazda Cars & Trucks

2 Answers

I have a 2006 chevy trailblazer i change all the mounts inclunding the idol tentionor and its still vibrates and make niose when am in drive or reverse in park and neutal its fine but just when am in

If the harmonic balancer wobbles when the engine is running, it could cause a vibration. A typical balancer has a rubber seal between the balancer and the belt drive pulley. The rubber seal may have deteriorated.

Dec 27, 2014 | 2006 Chevrolet Trailblazer

1 Answer

I have a 1995 mazda miata that needed a new harmonic balancer, new battery, and oil. It was working fine until I was coming home from work ( after putting 10W-40 and 10W-30 motor oil in it) and had noticed...

Any Noises and/or Stalling or Misfire(s) ?
Will Engine Crank ? If so does it Crank Fast or Slow and/or Really Slow like rrrruh....rru...rrru..rrururu .
POSSIBILITY - ALTERNATOR BAD or going BAD it' not generating power to keep the battery charged therefore causing all Electronics to slowly fail as the battery loses all life ?
Need more Info and Why was a HARMONIC BALANCER needed? The obvious of course it was bad , But you are driving a MAZDA and a harmonic balancer isn't just a harmonic balancer it has to be the EXACT HARMONIC BALANCER , they can look identical and still be different . What was the REASONING for the replacement?NOT A COMMON PROBLEM.

Dec 05, 2013 | Cars & Trucks

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on

the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

1 Answer

How do i remove the harmonic balancer on my 1994 mazda 626 , 6 cylinder? which direction do i turn it?

you need a puller to remove a balancer,, whenever doing motor work,, always turn the parts in the same direction they turn while running, never the other way

Jul 15, 2011 | Mazda 626 Cars & Trucks

2 Answers

I have a knock in the front of the moter in the pullys or harmonic balncer should you have free play in the balncer

No there should be no free play in the balancer. There is a rubber ring in the middle of two steel sections on that balancer that will rot out and cause a knockign issue and free play as you describe.

Jan 21, 2011 | 1994 Oldsmobile Ninety Eight Regency

2 Answers

Where is the crank sensor located on a 1999 oldsmobile intrigue 3.5 engine???? easy to replace or not...

usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.

Dec 01, 2009 | Oldsmobile Intrigue Cars & Trucks

2 Answers

Alternator not charging the battery.. Do you know where the alter

You own a mini van. These creations were designed by engineers to drive mechanics crazy! :-( Everything is designed with little or no access. The alternator on your van is made of aluminum (so it's silver). It is located near the crankshaft harmonic balancer. If you look at the harmonic balancer, the alternator will be at the 10 o'clock position. It is on the passenger side of the engine, behind the engine block. One of the fan belts goes to it. The pulley on the alternator has a belt on it. Follow the fan belt which goes towards the rear of the engine.
PS You may have to get under the van to remove it.

Nov 16, 2008 | 1989 Mazda MPV

1 Answer

Harmonic balncer

Hi there,
it seems that your explanation is a little bit confusing. Could you tell me what engine( 4D56??) and describe a little bit more in details about the pin you are worried about?

Oct 22, 2008 | 2002 Mitsubishi Montero Sport

Not finding what you are looking for?
1994 Mazda 626 Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides