Question about 1989 Nissan Stanza

1 Answer

Any free downloadable manual for removing or disassembling a '91 nissan stanza automatic transmission. I want to have this trans fixed or replaced because it is not working or moving when "D" is selected. Any other solution out there to consider before removing/uninstall trans. Thanks...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 75 Answers

You may want to check the linkage for adjustment or the shift cable for excessive wear.

Posted on Apr 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 91 Nissan truck just purchased, it's stuck in reverse and 5th gear, how do I fix


If the problem is in the shifter lever assembly, you can remove that from the top of the transmission after you remove the floor mat/carpeting, slide up the boot, and remove the six bolts holding it to the transmission. But, if everything seems to be free and moving smoothly in that assembly, the transmission will have to be disassembled to find which shift forks or associated rods are bound up or broken.

Jan 02, 2017 | Nissan Cars & Trucks

1 Answer

Transmission fluid is pour out near the back of the transmission on my automatic 2.4 liter 1990 nissan stanza. what possible problems does that tell me about?


One of your axle shaft seals or the speed sensor o-ring is leaking. Those are the only three things back there that can be leaking. Have them all checked out and replaced as needed.

Sep 07, 2011 | 1990 Nissan Stanza

1 Answer

93 nissan d21 4 cyl automatic trans wont shift into OD. rpms reach 4000 at 65 mph.. what is the problem?


well there are a few reasons that could cause this problem some of which are easy fix others are a major fix.
1)The throtle valve cable could be out of adjustment, for this to be corrected it is best to be taken to a transmission shop, or you could buy a Chilton or Haynes repair manual to see how to adjust it yourself.

2)The O.D. solenoid (which depending on the transmission in the truck) is either inside or on the outside of transmission, could have a bad wire going down to it, or have a bad connection to it, or it may not any power getting to it /// First Check All Fueses on vehicle then locate where solenoid is the check wires for power. The solenoid could also be plugged or bad depending on condition of trans and the ATF.

3)In side the transmission the is whats called a Over Drive Clutch Pack and the cluthes could be worn out or completely gone this happens quite often with older vehicles. If this happens to be the problem then the only possible fix would be what is called a OVER HAUL in which the transmission is removed from the vehicle, disassembled, all clutches and damaged parts in side are replaced, then transmission is or should be cleaned and then reassembled and then the transmission is reinstalled back into the vehicle.


So depending on where you live there might be a transmission shop that might diagnose the exact problem of your 93 nissan and give you a quote on fixing it. Some shops do this for free other do not. My shop does this for free. So I hope this helps you with your truck.

Jan 04, 2011 | 1993 Nissan Pickup

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

Transmission , trans is slipping after it warms up, or after few miles, can it be my filter dirty? or do you think it needs to be replaced or rebuilt? rb


For any auto transmission always think basic solution, in this case change the filter, replace with new fluid, Sure repair shops want to replace the entire unit,why more money. a new trans will fix the problem. but so might a filter and fluid change do the trick for alot less money. New trans costs 2500.00 filter and fluid 50.00. you do the math

May 13, 2010 | 1991 Nissan Stanza

2 Answers

How much would it cost to replace a '91 Nissan?


1200 to 1500 for a used motor including about 800 for labor and 700 for the motor and shipping at a normal shop (not a dealership)

Apr 10, 2010 | 1991 Nissan Stanza

1 Answer

!992 nissan stanza standard trans fluid


If your referring to the manual transmission where you do the shifting. Your going to be using gear lube, not to be confused with transmission fluid. Which is red in color, they are not interchangeable transmission fluid is only for automatic transmissions. Gear lube is much heavier in weight, you want to get a gear lube 80-90 weight this lube is perferred for your vehicle

Apr 03, 2010 | 1991 Nissan Stanza

1 Answer

Transmission started gushing fluid out.


THAT sounds like the foward pump housing cover and the only thing to do is to take it to the auto trans people as it has to be remover and replaced from inside
I could be wrong but i dont think so
LET ME KNOW HOW YOU GO Ron

Oct 03, 2009 | 1990 Nissan Stanza

1 Answer

AUTOMATIC TRANSMISSION WON´T MOVE


That trans is an RE4FO2A or V and check the fluid level,if the fluid level is good,check the axles to make sure they are seated all the way in the trans,and that the axle's CV joints aren't broken.Other than that,likely an internal problem with the forward clutches,torque convertor,or pump assembly.

Jul 08, 2008 | 1992 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...