Question about 1998 Ford Mustang

1 Answer

How do you change a tentioner pully on a 98 mustang 3.8

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 260 Answers

  1. Remove belt
  2. loosen tensioner pulley bolt(9a) and remove tensioner.


how do you change a tentioner pully on a 98 - 5c3c06b.gif

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ac not working


lots of possibilitys, 1. blown fuse
2. low on refrigerant, will not let the pully to engage
3 nothing bad about fords, but they use plastic for air dams, inside of the hot and cold deck
4. try to change from cold to hot if it does not change refer to 3.
hope this helps

Aug 13, 2013 | 2000 Ford Mustang

1 Answer

Where is belt tensioner and how do you turn it to loosen belt to change


The belt tentioner pully is the idler pully in the serpentine belt system...
You need a long wrnch (11/16??) to fit the pullys center bolt...
Turn the bolt to the right ( righty tighty) and the tentioner will losten its tention on the belt enough to remove the belt...
Imediately replace the belt ... so its routing is not forgotten by time or distraction...
If there is still a sticker on the upper radiator support reflecting the serpintine belt routing.. then you are in a better spot to be doing this ... with distractions...

Oct 06, 2010 | 1995 Chevrolet K2500

1 Answer

How to losen the tention pully


there is a nut that is in the center of the pully... turn it as if you were tightening it... this action should cause the whole unit to swivle... thus releasing the tention on the belt.

Sep 30, 2010 | Chevrolet Aveo Cars & Trucks

1 Answer

Replace bearing to pulley tensioner


Remove belt, remove tentioner ,remove bolt holding pully on,replace pully and bearing,put tentioner back on, put belt back on.

Apr 11, 2010 | 1997 Saab 900

1 Answer

I cannot get the serpintine belt back on the pully after changing the water pump is there an adjusting screw abd where would I find it 1996 pontiac sunfire


there should be a tention pully that is spring loaded and you will need a socket to fit the bolt in the center. then turn clock wise and hold to release tention and set belt in place then slowly release the pully

Jan 16, 2010 | 1996 Pontiac Sunfire

1 Answer

How to change timing belt


This is how 2.8TD.Remove the belts (fan and power steering)with a 10mm socket un-screw the plastic cover. To remove the bottom pully their is 3 small screws inside the pully (10mm or 12mm) unscrew them and take off the pully. Do not try to remove the big nut. Remove the plastic cover. Their is a small hole in all the drive wheel's their is a treaded hole in the engine block behind each one and a mark on the crank shaft. Turn the engine until the mark on the crankshaft is at the top then push the bolts ( metric course tread 12 or 13 mm head 4 to 5 ins long) through the holes in the drive wheel's and try to screw them in if they dont line up first time turn the crankshaft 1 turn and try again. When they all line up screw in the bolds this keeps the timing in place. Release the tention pully (the one with no tracks on and pushing against the back of the belt) remove the old belt replace. To tighten the tention pully put a small socket bar in the square hole turn until the belt is tight hold the preasure on the socket bar ant tighten the locking screw. Remove the screws job done.

Jun 11, 2009 | 1995 Isuzu Rodeo

1 Answer

Changing ac compressor belt


This should be a serpentine belt that is held in place with a spring loaded belt tensioner. There shold be a label under the hood showing the correct belt orientation. You need to have a long open end wrench or box wrench tentioner forward, addition tention to it to allow the belt to be slipped over one or the other pullys, once this is done, the belt should be tight. If it is over all the pullys and still loose, you either have the wrong belt or the tensioner is bad.

May 23, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

2000 isuzu rodeo removal and installation of serpentine belt


All u need to do is put a wrench on the tention pully and turn it clockwise... this will relive the tention take off the old belt ....put on new one. repeat relive pressure again ...slip it on pully... and relese tention..... done! :)

May 16, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...