Question about 2004 Chrysler Crossfire

1 Answer

Canot turn off the gas filler door open image on my instrument cluster

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 244 Answers

Open fuel filler door and see if switch isn't stuck and that the door hits the switch when closing door.

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Ford E350 Van Door locks & dome lights are going on & off on there own


Do you know anything about automotive electronic's ? Control modules ?
Vehicle Security Module
The vehicle security module receives inputs from the following:
  • Door ajar switches
  • Keyless entry keypad
  • Ignition switch
  • Remote keyless entry (RKE) transmitter
The vehicle security module uses these inputs to control an output signal to the instrument cluster which controls the battery saver relay and interior lamp relay. The battery saver relay and the interior lamp relay are internal to the instrument cluster, and are not replaceable. There could be a faulty switch input to the I/C - insturment cluster , causing the vehicle security module to activate the lock's an light's .
Interior Lighting Systems
The instrument cluster grounds the battery saver relay and interior lamp relay coils when any door ajar switch is opened, or the interior lamp (headlamp) switch is closed. The interior lamp relay then supplies voltage to the interior lamp circuit. Vehicle speed must be less than 24 km/h (15 mph) for the instrument cluster to ground the interior lamp relay. The interior lamps remain illuminated for up to 25 seconds after all doors are closed unless the instrument cluster receives an input from any of the following:
  • voltage from the ignition switch.
  • a vehicle speed signal.
  • input from the keyless entry keypad through the vehicle security module.
  • input from the RKE transmitter unlock or panic switch through
  • the vehicle security module.
Do you know what DTC'S - diagnostic trouble codes are ?
Could have DTC'S stored in the following Modules
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1320 Driver Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test C . B1328 Passenger Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test C . B1342 ECU is Defective Instrument Cluster CLEAR the DTCs. REPEAT the self test. If DTC B1342 is retrieved again, INSTALL a new instrument cluster. REFER to Section 413-01 . All Other DTCs - Instrument Cluster REFER to Section 419-10 .


Vehicle Security Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1322 Driver Door Ajar Circuit Short to Ground Vehicle Security Module Go To Pinpoint Test C . B1330 Passenger Door Ajar Circuit Short to Ground Vehicle Security Module Go To Pinpoint Test C . B1338 Door Ajar RR Circuit Short to Ground Vehicle Security Module Go To Pinpoint Test C . B1342 ECU is Defective Vehicle Security Module CLEAR the DTCs. REPEAT the self test. If DTC B1342 is retrieved again, INSTALL a new vehicle security module. REFER to Section 419-10 . B1574 Door Ajar LR Circuit Short to Ground Vehicle Security Module Go To Pinpoint Test C . All Other DTCs - Vehicle Security Module REFER to Section 419-10 .
Your best bet mite be to take to a qualified repair shop .

Sep 05, 2017 | Ford Cars & Trucks

1 Answer

Fuse location for interior lighting 2007 f150 fxt4x4 also is there 2 dash lights it doesn't seem to be as bright as it used to


dash lights it doesn't seem to be as bright as it used to ???? Dimmer switch on full bright ? Visual Inspection Chart Electrical
  • Bulbs
  • Central junction box (CJB) fuse 24 (15A)
  • Circuitry
  • Vehicle security module (if equipped with RKE)
  • Instrument cluster
  • Door ajar switches

Interior Lighting The interior lamp system is separated into 2 subsystems: the interior lamp subsystem and the on-demand lamp subsystem. The dome light and front map light on-demand lamps are also part of the interior lamp subsystem.
An on-demand interior lamp will only illuminate when its specific switch is activated. On-demand lamps consist of the front map light and the dome light.
The instrument cluster illuminates the interior lamps when any door is ajar, when an unlock signal is received by the vehicle security module (if equipped with remote keyless entry (RKE) or the dimmer switch is rotated to the ON position. The instrument cluster will turn off the interior lamps when all doors are closed, the vehicle security module (if equipped with RKE) receives a lock signal, 25 seconds have elapsed since the illuminated entry feature was activated, or the dimmer switch is rotated to the OFF position.
The vehicle is also equipped with a battery saver feature. The battery saver feature provides automatic shutoff of the demand lamps, courtesy lamps, and the warning chimes after a specific period of time has elapsed in order to save battery power.

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN, ISO or UBP circuits fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for instrument cluster, refer to Section 413-01 .
    • No response/not equipped for vehicle security module, refer to Section 419-10 .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the instrument cluster.
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the vehicle security module.
  1. If the DTCs retrieved are related to the concern, go to the Instrument Cluster Diagnostic Trouble Code (DTC) Index or the Vehicle Security Module Diagnostic Trouble Code (DTC) Index.
  1. If no DTCs related to the concern are retrieved, GO to Symptom Chart .
  2. Symptom Chart Condition Possible Sources Action
    • The interior lamps are inoperative
    • Fuse
    • Circuitry
    • Instrument cluster
    • Dimmer control switch
    • Go To Pinpoint Test A .
    Pinpoint Test A: The Interior Lamps Are Inoperative
    Normal Operation On vehicles equipped with remote keyless entry (RKE), the door ajar switches are hardwired to the vehicle security module. The vehicle security module monitors the status of all door ajar switches, and when a door is opened, transmits a dome lamp ON signal to the instrument cluster through UART based protocol (UBP) circuit 1906 (PK), indicating a door has been opened. When the instrument cluster receives the dome lamp ON signal from the vehicle security module, the instrument cluster energizes the interior lamp circuits, which illuminates the interior lamps and, if equipped, the puddle lamps in the exterior mirrors.
    On vehicles without RKE, the door ajar switches are hardwired to the instrument cluster. When the driver or passenger door is opened, the instrument cluster receives a ground signal from the driver door ajar switch through circuit 344 (BK/YE), or from the passenger door ajar switch through circuit 345 (BK/PK), and the instrument cluster energizes the interior lamp circuits, causing the interior lamps to illuminate.
    The dimmer control switch can be used to turn the interior lamps ON or OFF when the doors are closed. The interior lamp defeat switch can be used to turn the interior lamps OFF when the doors are open.
      Possible Causes
    • Fuse
    • Circuit 53 (BK/LB) open or short to ground
    • Circuit 57 (BK) open
    • Circuit 402 (OG/LG) open
    • Circuit 1405 (LB/BK) short to ground
    • Circuit 3049 (BK/LG) open
    • Dimmer control switch
    • Instrument cluster
    PINPOINT TEST A: THE INTERIOR LAMPS ARE INOPERATIVE
  3. PINPOINT TEST A: THE INTERIOR LAMPS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK THE INTERIOR LAMP OPERATION AT THE DIMMER CONTROL SWITCH
    • Close all doors.
    • Operate the interior lamps with the instrument panel dimmer control switch.
    • Do any interior lamps illuminate?
    Yes
    For vehicles without RKE, REFER to Section 413-01 .

    For vehicles with RKE, REFER to Section 419-10 .

    No
    GO to A2 . A2 CHECK FOR INSTRUMENT CLUSTER OR VEHICLE SECURITY MODULE DIAGNOSTIC TROUBLE CODES (DTCs)
    • Key in ON position.
    • Carry out the instrument cluster On-Demand Self Test.
    • For vehicles equipped with remote keyless entry (RKE), carry out the vehicle security module On-Demand Self Test.
    • Were instrument cluster DTCs B2499 or B2659, or if equipped with RKE, vehicle security module DTC U1950 present?
    Yes
    For instrument cluster DTC B2499, GO to A5 .

    For instrument cluster DTC B2659, GO to A9 .

    If equipped with RKE and vehicle security module and DTC U1950 is present, REFER to Section 418-00 to diagnose the UBP network concern before attempting to diagnose the interior lighting concern.

    No
    GO to A3 . A3 CHECK CIRCUIT 3049 (BK/LG) FOR AN OPEN
    • Key in OFF position.
    • Disconnect: Instrument Cluster C220b.
    • Measure the voltage between the instrument cluster C220b-9, circuit 3049 (BK/LG), harness side and ground.
    • Is the voltage greater than 10 volts?
    Yes
    GO to A4 .

    No
    VERIFY the central junction box (CJB) fuse 21 (15A) is OK. If OK, REPAIR the circuit. TEST the system for normal operation. A4 CHECK INSTRUMENT CLUSTER CIRCUIT 57 (BK) FOR AN OPEN
    • Disconnect: Instrument Cluster C220a.
    • Measure the resistance between the instrument cluster C220a-17, circuit 57 (BK), harness side and ground.
    • Is the resistance less than 5 ohms?
    Yes
    GO to A5 .

    No
    REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test. A5 CHECK CIRCUIT 53 (BK/LB) FOR AN OPEN
    • NOTE: If the fuse fails, repair circuit 53 (BK/LB) for a short to ground.
    • Connect a fused (15A) jumper wire between the instrument cluster C220b-9, circuit 3049 (BK/LG), harness side and the instrument cluster C220b-8, circuit 53 (BK/LB), harness side.
    • Do the interior lamps illuminate?
    Yes
    REMOVE the jumper wire. GO to A6 .

    No
    REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test. A6 CHECK THE DIMMER CONTROL SWITCH OPERATION
    • Connect: Instrument Cluster C220a.
    • Disconnect: Dimmer Control Switch C205b.
    • Connect a fused (15A) jumper wire between the dimmer control switch C205b-4, circuit 57 (BK) and the dimmer control switch C205b-2, circuit 402 (OG/LG).
    • Do the interior lamps operate?
    Yes
    INSTALL a new dimmer control switch. REFER to Section 417-01 . TEST the system for normal operation.

    No
    GO to A7 . A7 CHECK CIRCUIT 402 (OG/LG) FOR AN OPEN
    • Disconnect: Instrument Cluster C220a.
    • Measure the resistance between the instrument cluster C220a-12, circuit 402 (OG/LG), harness side and the dimmer control switch C205b-2, circuit 402 (OG/LG), harness side.
    • Is the resistance less than 5 ohms?
    Yes
    GO to A8 .

    No
    REPAIR the circuit. TEST the system for normal operation. A8 CHECK DIMMER CONTROL SWITCH CIRCUIT 57 (BK) FOR AN OPEN
    • Measure the resistance between the dimmer control switch C205b-4, circuit 57 (BK), harness side and ground.
    • Is the resistance less than 5 ohms?
    Yes
    GO to A11 .

    No
    REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test. A9 CHECK CIRCUIT 1405 (LB/BK) FOR A SHORT TO GROUND
    • Key in OFF position.
    • Disconnect: Instrument Cluster C220a.
    • Disconnect: Dimmer Control Switch C205b.
    • Measure the resistance between the instrument cluster C220a-11, circuit 1405 (LB/BK), harness side and ground.
    • Is the resistance greater than 10,000 ohms?
    Yes
    GO to A10 .

    No
    REPAIR the circuit. TEST the system for normal operation. A10 CHECK THE DIMMER CONTROL SWITCH
    • Carry out the dimmer control switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Is the dimmer control switch OK?
    Yes
    GO to A11 .

    No
    INSTALL a new dimmer control switch. TEST the system for normal operation. A11 CHECK FOR CORRECT INSTRUMENT CLUSTER OPERATION
    • Disconnect all instrument cluster connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all instrument cluster connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    INSTALL a new instrument cluster. REFER to Section 413-01 . TEST the system for normal operation.

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation

Jul 19, 2017 | Cars & Trucks

1 Answer

Just got my 2003 explorer sport trac dome light dont come on when you open the doors but they come on when you push the button to turn them on how do I get them to come on when I open the doors?????


The instrument cluster illuminates the interior lamps when an unlock signal is received from the vehicle security module. The illuminated entry feature will be canceled when any of the following conditions are met:
  • 25 seconds have elapsed since the illuminated entry feature was activated and the interior lamp control is not activated (door ajar or courtesy lamp switch on).
  • The instrument cluster receives a request from the vehicle security module (remote transmitter lock button pressed) and the interior lamp control is not activated.
  • The ignition is in the RUN or START position and the interior lamp control is not activated.
The instrument cluster illuminates the courtesy lamps when any door is open or ajar. The courtesy lamps shuts off when the doors are closed and the illuminated entry feature is not active or when the vehicle speed is greater than 5 mph (8 km/h). The interior lamps are not reactivated until the vehicle speed is less than 3 mph (5 km/h) and a new door open warning lamp signal is received.
The instrument cluster controls the courtesy lamps illuminated entry function by activating the battery saver relay.
The panel dimmer switch is integrated into the headlamp switch and controls the interior lamps by activating the instrument cluster through circuit 1034 (BK/WH).
The vehicle security module sends a signal to the instrument cluster on the UBP network circuit to indicate a request to turn the illuminated entry feature on or off.
The on-demand lamps, glove compartment assembly, homelink module, puddle lamps and illuminated vanity mirrors are controlled by the battery saver relay. The battery saver relay becomes active (relay coil is energized) when the instrument is in the awake mode, or in the sleep mode (relay coil is de-energized).

Nov 28, 2016 | 2003 Ford Explorer Sport Trac

2 Answers

2003 navigator interior Lights and driving lights won't turn off. Door ajar warning on


Is your 'door ajar' or 'dome light' staying on? Forum members suggest various methods that they fixed their issue. The methods include:
  • Adjusting the dimmer
  • Spraying the switch with a lubricant
  • Replacing the switch
  • Replacing the relay

Sep 28, 2016 | Cars & Trucks

1 Answer

How do I change the dimmer switch to my Pontiac grand prix


Disconnect the battery ground negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical. Remove the left instrument panel (IP) insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side . Remove the steering column filler. Refer to Steering Column Opening Filler Replacement . Remove the knee bolster bracket. Refer to Knee Bolster Replacement . Lower the steering column. Refer to Steering Column Replacement in Steering Wheel and Column - Tilt. Remove the instrument panel cluster (IPC) trim plate. Refer to Instrument Cluster Trim Panel Replacement in Instrument Panel, Gages and Console. Grasp the headlamp switch and pull firmly to release the retaining tabs from the instrument panel. Disconnect the electrical connector from the headlamp switch. Remove the headlamp switch.



Grasp both sides of the bottom edge of the instrument panel cluster (IPC) trim plate and pull out in order to release the retainer clips. Disconnect the electrical connector from the fog lamp switch. Remove the trim plate from the IP.




qqezpewk1waaaabjru5erkjggg==

gaaaabjru5erkjggg==

Jan 14, 2015 | 2002 Pontiac Grand Prix

1 Answer

I have a 2002 Saturn sc2 coupe, none of the interior instrument cluster/dash lights work. I am havinf a heck of a time finding a fuse box diagram, which fuse controls those lights? The panel doesn't h


The fuse panel is on the side of the dash where the drivers door opens up. The cover is right there. The diagram is on the back of the fuse panel cover. It will say cluster or dash Lts. If fuse is good try turning dimmer dial on left side of dash, it may be turned down just below gas guage

Oct 15, 2014 | Saturn SC2 Cars & Trucks

1 Answer

The turn signals , displays on radio unit will not work completly


this is a short circuit on the bus network.
1- i would examine the exterior temperature sensor and that the two wires are not in contact.
2- on the rear right side of the trunk there is a white socket, make sure it has no water ingression in it.
3- take out the A/C head unit and try if things works.
4- Remove the instrument cluster and unplug its sockets and all should be working.

from the above we can detect what is causing this

Apr 22, 2009 | 2001 BMW 5 Series

1 Answer

I need a printable image of fuse block / 97 ford windstar


your owner manual sould have fuse chart. Some fuses/ekays in enine compartment. Some in car on left side of instrument panel

in car

1d470b5.gif
Fuse Amps Circuits Protected 1 10 Power Mirrors, Anti-Theft Warning Light, Diagnostic Connector 2 5 Generic Electronic Module, Start Interrupt Relay Coil 3 5 Radio Illumination, Remote Radio Illumination, Electronic Instrument Cluster, Electronic Instrument Cluster PRNDL Illumination, Electronic Instrument Cluster Switch Module, Analog Cluster Illumination, Instrument Illumination 4 — Not Used 5 — Not Used 6 15 Rear Quarter Windows (LH and RH) 7 15 High Mounted Stoplamp, Brake Shift Interlock 8 25 Subwoofer, JBL Amplifier 9 10 Park and Turn Lamps, Side Marker Lamps, License Lamps, Stop Lamps 10 2 High Beam Indicator Electronic Cluster 11 15 Park Lamps 12 10 Remote Radio, Auxiliary Warning Lamp Module, Remote Keyless Entry (RKE) Module, Anti-Theft Controller Module, Radio Illumination 13 15 Radio, CD Disc Changer 14 5 Electronic Chromatic Mirror, Analog Cluster Indicator Lamps, Air Bag Module 15 — Not Used 16 15 Horns, Horn Relay Coil 17 15 Fog Lamps 18 25 Front Wiper Motor, Front Washer Pump, Wiper/Washer Relays 19 10 Generic Electronic Module (Pin 57), Electronic Instrument Cluster 20 25 Integrated Relay Control Module, Ignition Coil 21 10 Air Bag Module, Rear Window Defrost Relay, A/C Clutch, Temp Blend Door Actuator, Brake Shift Interlock 22 20 Rear Cigar Lighter, Power Plug 23 15 Multi-Function Switch 24 20 Rear Wiper Motor, Rear Washer Pump 25 10 Turn Signal Lamps, Instrument Cluster Turn Indicator 26 15 LH Aero Headlamp, Left and Right Trailer Stop/Turn/Hazard 27 15 Hazard Warning Lamps, Instrument Cluster Turn Indicator 28 15 Instrument Panel Cigar Lighter 29 15 Battery Saver Relay, Interior Lamp Control Relay, Interior Lamps, RH and LH Keyhole Lamps 30 25 Backup Lamps, Electronic Cluster 31 10 Rear Air Suspension 32 15 RH Aero Headlamp, Trailer Park Lamps 33 15 Anti-Lock Brake (ABS) Relay, Anti-Lock Brake (ABS) Module, Daytime Running Lamp (DRL) Module 34 30 One Touch Relay, LH Window Motor 35 15 Anti-Theft Controller Module 36 30 A/C Mode Switch 37 20 Door Lock Actuators, Memory Door Lock Relay 38 15 Heated Mirrors (LH and RH) 39 30 Auxiliary Blower Motor, Ref. Valve Solenoid 40 30 Window Motor (RH) 41 5 Autolamp Relay Coils, Autolamp Sensor 42 — — 43 — — 44 — —

Mar 15, 2009 | 1997 Ford Windstar

2 Answers

Can't find heater fan


The heater fan is located under the dash on the passenger side. In the 2001 Lumina you have to take out the 2 plugs holding the insulation in to remove the insulation. The heater fan is at the very front butting up against the firewall. Removing the front-most bolt is a real pain in the ****, so it might be easiest to remove that first and install it last.

Aug 05, 2008 | 2001 Chevrolet Lumina

1 Answer

Gas gauge no longer works


The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

May 14, 2008 | 2007 Jeep Scout

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...