Question about 1988 Chevrolet Corsica

1 Answer

How do I replace the ignition switch on my 1988 corsica?

Posted by on

  • yadayada
    yadayada May 11, 2010

    the switch or the lock cylinder?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 267 Answers

You will need to pull the steering wheel to do this job
possibly available to rent from auto parts store
once wheel is off you need to remove lock ring by depressing it and removing clip ring. then remove turn signal assembly (4 screws) after this you should see the release screw ro the ignition switch. Is this a tilt column? If this helps get back to me a I can walk you thru it. dont forget to reply too - good luck
email is chromapr@wowway.com

Posted on Apr 26, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1608 Answers

SOURCE: 1988, 2.0 corsica. is the

Yes.Just follow the plug wires.There are 2 coils.Hope this helps.Good luck.

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 chevy corsica key stuck in the run position


ignition switch keylock cylinder is broken.

Apr 17, 2013 | 1988 Chevrolet Corsica

1 Answer

Print Email Problem with Chevrolet 1988 Corsica is hard to start after i get it started its runs good


hook up a fuel pressure gauge and run it check the fuel pressure let it sit with the gauge on it let sit for a little while and see if the fuel pressure drops off

Jun 04, 2012 | 1988 Chevrolet Corsica

1 Answer

My 4 cyl corsica acts like it runs out of fuel and visuyally duz as your lookin in the throttle body,then dies ive replaced fuel pump 2 times and filter once and plugs coils crank sensor ignition module...


buy another car.that thing cant be worth as much as you,ve spent on it.trouble shooting a repair by throwing parts at it isnt the way to go.did you try a mass air sensor

Nov 20, 2010 | 1988 Chevrolet Corsica

1 Answer

1988, 2.0 corsica. is the ignition coil at the bottom back of the motor.


Yes.Just follow the plug wires.There are 2 coils.Hope this helps.Good luck.

Nov 06, 2010 | 1989 Chevrolet Corsica

1 Answer

What is the firing order of the wires that go from the spark plugs to the coil pack or distrobuter for a 1988 4 cylinder chevy corsica


For the 2.0L:
Firing Order:
1-3-4-2
Cylinders:
1---2---3---4
(front of vehicle)
Ignition Connections:
----[4]
-------[1]
---------[3]
-----------[2]
(front of vehicle)

Feb 09, 2010 | 1988 Chevrolet Corsica

1 Answer

Need a wiring diagram from ignition module to coil to engine for a 1988 chevy corsica. Ive been replacing parts on this car for 6 months and it still runs like ****. It run good for one month now its...


This is for the 2.8L engine. Sometimes if it is hard to see, you can use a mirror and a flashlite. Aim the mirror in the direction of part your trying to look at, shine the lite in the mirror.
2.8-se0j5t3k3rpearckfykaa4pi-4-0.jpg

Jul 21, 2017 | 1988 Chevrolet Corsica

1 Answer

I have a 1991 corsica 3.1 auto. starts fine but about 3 or four seconds after I let key go the engine dies. What do I do to repair this?


You may have a short in the ignition switch and may need to replace ignition switch also have the starter solenoid checked

Jul 31, 2009 | 1991 Chevrolet Corsica

1 Answer

1988 chevy corsica 6 cyl suddenly running on 4


WET PLUD W/GOOD COMPRESSION IS USUALLY NO SPARK.YOUR ENGINE HAS 3 IGNITION COILS.EACH COIL CONTROLS 2 SPARK PLUGS.TRACE THE WIRES FROM THE BAD SPUGS BACK TO THE COILS .IF THEY ARE THE SAME COIL THEN U HAVE A BAD ONE OR CONTROL MODULE(UNDER COIL)

May 12, 2009 | 1988 Chevrolet Corsica

1 Answer

1988 corsica turn signal flasher unit


its under the dash panel and its a round plug that has 3 prongs Please rate myresponse thank you very much

Jan 30, 2009 | 1988 Chevrolet Corsica

Not finding what you are looking for?
Cars & Trucks Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...