Question about 2006 Chevrolet Silverado

1 Answer

Remove rear passenger door panel - 2006 Chevrolet Silverado

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 63 Answers

Not too bad a job to do, taking your time it should take 30-45 minutes. You will need a straight screwdriver, phillips screwdriver, a small set of sockets, a clip removal tool also comes in handy.

If you have manual windows, you will need to remove the clip holding the window crank in place. Usually the clip removal tool makes easy work of it by just pushing the clip out from under the window crank handle. If you have electric windows so much the better.

Roll down the window before beginning. Now depending on how Detroit was hiding things, you should look in the area of the door pull for screws that fasten the interior door covering to the door. These might be exposed but sometimes are hidden under plastic caps or trim parts. Very carefully remove this pieces as with age they do become brittle.

Once you are rather sure you have the fastening screws out of the way, using the straight screwdriver to ease the door panel away from the door along the bottom edge. By looking inside you should see one of two methods of fasteners. The older style are simply straight push in plastic clips, you release these by simply putting enough pressure of the panel to pull the clips out. The newer method has a clip that slides down about a 1/2 inch into a matching hole. These panels are removed by lifting up on the door panel and then out.

Installation is just a reversal of the removal procedure.

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door handles wont open doors


Fixed 1997 Ford Explorer Door wont open - YouTube

? 2:03
https://www.youtube.com/watch?v=Gs3eC8E-gbU
Sep 6, 2014 - Uploaded by craiwin
I fixed my 1997 Ford Explorer Door won't open problem! ... I have the same problem but my passenger side door on my 2001 Ford Explorer locked and won't open smh ... will this work for the rear passenger doors? ... How to Replace Rear Inside Door Handle Latch Cable 2002-05 Ford Explorer Mercury ...

98 Ford Explorer Door Won't Open Part 1 - YouTube

? 0:30
https://www.youtube.com/watch?v=oY4IcNdGK68
Apr 5, 2010 - Uploaded by gdellinger
A couple weeks ago the door handle just stopped working on the... 98 Ford Explorer Door Won't Open Part 1 ... The remote would open all other doors. ... on a Ford Exploer 91-2001 - Duration: 7:27. by diversity2 37,309 views.

98 Ford Explorer Door Problems- how to open without panel ...

? 4:22
https://www.youtube.com/watch?v=lJ0Fsh3561s
Jan 1, 2013 - Uploaded by inwinblades
98 Ford Explorer Door Problems- how to open without panel removal. inwinblades .... HELLO panel removal??? door won't open... Been searching all ... ok this better work on all doors, im aboutt o try this on my rear passenger door. .... I didn't care about the plastic door handle so i just "busted" it to pieces.

Rear doors can't open from inside - Ford Explorer and R





Jan 05, 2016 | 2001 Ford Explorer

2 Answers

How do you remove the rear passenger door panel on a 2012 ford Escape when the door is stuck in the closed position?


How To Install Replace Remove Rear Door Panel Ford ...

? 3:29
www.youtube.com/watch?v=AWYFeGmCKtQJun 15, 2012 - Uploaded by 1A Auto Parts How To Install Replace Remove Rear Door Panel Ford Escape01-07 1AAuto.com. 1A Auto Parts ... Published on Jun 15, 2012... Do you have a video that shows how to fix a ford escape 2001rear passenger door latch?

Sep 16, 2015 | 2012 Ford Escape

1 Answer

The rear passenger door locks do not work on our 1999 GMC Suburban. I've checked the fuses and they all work; I tried to physically pull the lock button but it will not move: and I attempted to open the...


If the lock button doesnt move look like you door lock actuator jam you have to find a way to move the rear panel by the inside and unlock it manualy

Mar 22, 2015 | 1999 GMC Suburban

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

1 Answer

Do I remove the entire cover or the little door thats atached to this cover on the passenger side? There are 3 brake lights that were recommended to replace. Driver side and passenger side plus the third...


Lamp, Rear Hi-Mount Lamp Assembly
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Raise the liftgate.
  1. Remove the liftgate door trim panel (46404) . Refer to Section 01-05 for the removal procedure.
Trim Panel, Liftgate Door Removal
  1. Disconnect thebattery ground cable (14301) .
  1. On vehicles with a rear window wiper, remove the three rear wiper motor cover screws and remove the rear wiper motor cover.
  1. Pry the liftgate door trim panel (46404) away from the liftgate.
  1. Disconnect the luggage compartment lamp electrical connector.

    n11098a.gif

  1. Remove the liftgate door trim panel
  1. Rotate the rear hi-mount lamp socket counterclockwise and remove it from the rear hi-mount lamp (13A613) .

    k20521a.gif

  1. Remove the two rear hi-mount lamp housing nuts and remove the rear hi-mount lamp lens and housing.

    k20523a.gif

Oct 18, 2010 | 1995 Ford Aspire

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

1 Answer

Rear actuator, when heat is on in front with controls in rear on heat, rear blows cold air


The actuator on the rear controlling the climate control door was bad, the 2 top door panels had to be removed, then removed the 1 door foot step panel on the rear passenger side and the rear bottom hatch panel, then you can pull the large side panel back enough to get into the control, simply unplug the unit and remove the screws and install in reverse order, it took roughly 30 minutes, very much worth the time to DIY, We saved $ 430.00.

Dec 11, 2009 | 2003 Ford Expedition

2 Answers

AC needs a charge and how do I take the inside door panels off?


the a/c fitting are under the hood. they should be along the passenger side of the motor near the fire wall. don't put any r134a with sealant in it. only pure R134A.

Aug 06, 2009 | 1996 Lincoln Town Car

1 Answer

Remove rear passnger rear door panel 1991 honda


As I remember, you need to remove the front seat belt mount, & completely remove the back seats, in order to remove the rear door cards, without breaking them.
Have fun;)

Jul 17, 2009 | 1991 Honda Accord

1 Answer

Passengers side rear view mirro replacement


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Nov 30, 2008 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...