Question about 2000 Dodge Caravan

Open Question

Intake Plenum Torque Sequence - 2000 Caravan

What is the proper torque and torque sequence for the intake plenum on a 2000 Dodge Caravan with the Mitsubishi 3.0l engine?
Thank you for your help!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2841 Answers

SOURCE: Missing vacuum line on 2000 Dodge Caravan 3.0L

I do not have the solution for you but I will make a suggestion if you do not get an answer from someone else. Find a 2000 Dodge Caravan like yours at a used car lot and pop the hood and take a look. That may be your quickest solution.

Posted on Nov 17, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: What is the sequence for the bolts on oil pan, for

For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Posted on Jul 12, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

  • 40 Answers

SOURCE: replacing intake manifold plenum

what the hell is the question here? nothing. remove old one and put new one in.

Posted on Sep 08, 2009

  • 1244 Answers

SOURCE: Need torque sequence and torque specs for intake

bottom intake bolts torque 15-18 ft lbs from center and in criss cross pattern top plenum bolts 12-14 ft lbs

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge caravan 2009 4L intake plenum torque


Tighten bolts gradually starting in the center working outward until a torque of 12 Nm (105 in. lbs.) is obtained.

Sep 26, 2016 | Dodge Caravan Cars & Trucks

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Upper Intake Plenum Gasket R+R Torque Sequence


I cannot post a picture here because that is copyrighted material. However, the torque sequence is always "start in the center and work your way out to both ends...pretty simple.

The torque specifications are different depending on which engine your Escape is equipped with.

Apr 23, 2012 | 2004 Ford Escape

1 Answer

Torque specs on intake plenum and fuel rail on a 98 ford Ranger with a 4.0l




Hi the torque spec for this fuel rail/manifold is 9-11lb/ft. Here is pic of the sequence.

2011-03-28_205720_fuel.jpg



Jan 10, 2012 | 1998 Ford Ranger SuperCab

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

1 Answer

Looking for torque specs and sequence of both intake manifold and plastic plenum on 98 pontiac bonneville 3.8 non turbo


Lower intake bolts 11 ft. lbs start in the center of the intake and work your way out cross from side to side.Tighten the upper intake bolts with the same procedure with 89 inch pds.Be sure to apply threadlocker to the lower intake bolt threads.

Feb 07, 2010 | 1998 Pontiac Bonneville

1 Answer

Need torque sequence and torque specs for intake plenum on 3.5L 02 Olds Intrigue.


bottom intake bolts torque 15-18 ft lbs from center and in criss cross pattern top plenum bolts 12-14 ft lbs

Jan 22, 2010 | Oldsmobile Intrigue Cars & Trucks

1 Answer

What is the sequence for the bolts on oil pan, for 2000 dodge grand caravan? What is the torque for bolts for oil pan for 2000 dodge grand caravan?


For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Jul 12, 2009 | 2005 Dodge Caravan

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...