Question about 1996 Mercury Villager

1 Answer

Where can i find a diagram of the 1996 mercury villager water pump placement

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

I can sell you a shop manual ans wiring book for $25 plus postage or you can go to our website.

http://groups.yahoo.com/group/villagerquest/

  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures.
  1. Raise and support the vehicle.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.




  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover (6019).




  1. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation.

    Remove the six water pump bolts.




  1. Remove the water pump.
Installation
  1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material.

    Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block.




  1. NOTE: Refer to the note made during removal for the location of the stud/bolt.

    Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft).
  1. Position the water pump pulley on the water pump and install the four water pump pulley bolts.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
  1. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
  1. Install the crankshaft pulley. Refer to the procedure in this section.
  1. Lower the vehicle.
  1. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures.
  1. Connect the battery ground cable.
  1. Fill the cooling system. Refer to Section 03-03 for the procedure.
  1. Start the engine (6007) and check for leaks.

Posted on Apr 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need diagram for 1995 Mercury villager 3.0 to change timing belt


that engine is built by nissan believe it or not. look on the net for your van or a nissan maxama. I just googled it and found lots of diagrams for that van(95 mercury villiger 3.0 timing belt diagram. I would not only replace the belt, I would replace it using a timing belt replacement kit.If your going to keep the van.

Nov 17, 2011 | Cars & Trucks

1 Answer

Routing for a 1996 mercury villager


go here and read files on proper adjustment of a/c belt to prevent crank damage.
http://groups.yahoo.com/group/villagerquest/

please rate, thanks

fe71667.gif

May 31, 2010 | 1996 Mercury Villager

1 Answer

Where is the fuel pump on a 1996 mercury villager.


It's located inside the gsoline tank, if you're to change it, be sure to take the necessary precautions.

Jul 17, 2009 | 1996 Mercury Villager

1 Answer

1995 Mercury Villager Coolant crossover tube leaking


not likely. You may have to remove the upper intake manifold for access.

go to site for picture of heater hose diagram
http://autos.groups.yahoo.com/group/villagerquest/

Oct 19, 2008 | 1995 Mercury Villager

Not finding what you are looking for?
1996 Mercury Villager Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...