Question about 2002 Hyundai Santa Fe

1 Answer

How to replace head lights covers - 2002 Hyundai Santa Fe

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

I assume you are talking about the assembly. if so then there are 2 or 3, 10mm bolts on top of the assembly. remove them then pull the whole assembly out.

Posted on Apr 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motorized head light cover, back up lights


check fuses and bulbs first if good replace neutral safty switch for revers lamps and replace cover motors or just diable them and manualy open teh covers to the open position car isnt worth replacing motors if there even avalible

Feb 10, 2014 | 1988 Chrysler New Yorker

1 Answer

Water in light cover lens


The head lamp assembly should be sealed, you can either replace them or...... remove them and drill a small hole or two in the bottom to allow the moisture to exit. I have done this on a number of vehicles and it works great

Feb 25, 2013 | 1995 GMC Yukon

1 Answer

The head lights are on but the back lights don't


Open the boot, then remove the cover of the back light then replace the bulb.

Sep 25, 2011 | 1989 Toyota Camry

2 Answers

Valve cover gasket, how to replace?


Rocker Arm (Valve) Cover REMOVAL & INSTALLATION 2.3L 4-Cylinder Engines
  1. Disconnect the negative battery cable.
  2. Label and remove the spark plug wires.
  3. Remove the attaching bolts for the valve cover.
  4. Remove the valve cover from the cylinder head. If necessary, lightly tap the valve cover with a soft hammer to aid in removal. To install:
  5. Thoroughly clean the valve cover and cylinder head gasket mating surfaces.
  6. Install the valve cover on the cylinder head using a new gasket.
  7. Tighten the valve cover bolts to 14 ft. lbs. (20 Nm) in a crisscross pattern.
  8. Install the spark plug wires.
  9. Connect the negative battery cable.
  10. Start the engine and check for leaks. Fig. 1: Valve cover and gasket assembly 90953g12.gif
2.8L 6-Cylinder Engine
  1. Disconnect the negative battery cable.
  2. The following steps are necessary if your car has A/C and if you are removing the passenger side valve cover, if you do not need to remove the passenger side valve cover, skip them.
    1. Remove the A/C compressor belt and the compressor from the mounting bracket located on the passenger side of the engine. Do not remove the lines from the compressor.
    2. Place the compressor with the lines attached on the passenger side front shock tower and secure.
    3. Remove the compressor bracket.
  3. Remove the air cleaner-to-throttle body hose.
  4. Label and remove all necessary electrical and vacuum connections.
  5. Remove the attaching bolts for the valve cover(s).
  6. Remove the valve cover(s) from the cylinder head(s). If necessary, lightly tap the valve cover with a soft hammer to aid in removal. To install:
  7. Thoroughly clean the valve cover(s) and cylinder head gasket mating surfaces.
  8. Install the valve cover(s) on the cylinder head(s) using new gaskets.
  9. Tighten the valve cover bolts to 11 ft. lbs. (15 Nm) in a crisscross pattern.
  10. Install all necessary electrical and vacuum connections.
  11. Install the air cleaner assembly.
  12. Install the A/C bracket (if removed).
  13. Install the A/C compressor and belt (if removed).
  14. Connect the negative battery cable.
  15. Start the engine and check for leaks.
2.3L and 2.4L 5-Cylinder, and 2.9L 6-Cylinder Engines The 2.3L and 2.4L 5-cylinder, and 2.9L 6-cylinder engines have a two-piece cylinder head, the upper half and the lower half. The upper half is basically the same as a valve cover, except that it incorporates the bearing caps for the camshafts into the underside.
  1. Disconnect the negative battery cable.
  2. Remove the spark plug access cover.
  3. Label and remove the ignition coils and vent hoses or the distributor cap and wires if equipped.
  4. Check the cam alignment before removing the cylinder head.
  5. Remove the bolts attaching the upper cylinder head.
  6. Remove the upper cylinder head, lightly tap with a soft hammer if necessary. To install:
  7. Thoroughly clean the upper and lower cylinder head gasket mating surfaces.
  8. Apply liquid sealing compound to the upper cylinder head mating surface. WARNING
    Use a roller or your finger to spread sealant, do not use an excessive amount of sealant, or the oil passages could become clogged.
  9. Place the upper cylinder head onto the lower cylinder head.
  10. Check the cam alignment before tightening the cylinder head.
  11. Install Volvo tool number 5454 or equivalent to the upper cylinder head.
  12. Tighten the nut on the tools to seat the upper cylinder head.
  13. Tighten the upper cylinder head bolts, beginning from the center out to 13 ft. lbs. (17 Nm).
  14. Install the ignition coils and hoses or the distributor cap and wires.
  15. Install the spark plug access cover.
  16. Connect the negative battery cable.
  17. Start the vehicle and check for leaks. Fig. 2: Remove the clamp and detach the vent hose 90953p66.jpg
    Fig. 3: Remove the spark plug cover and the plug wires or ignition coils to access the retaining bolts 90953p80.jpg
    Fig. 4: Remove the retaining bolts 90953p72.jpg
    Fig. 5: A light tap with a soft-faced hammer is usually required to loosen the valve cover 90953p81.jpg
    Fig. 6: Carefully lift the upper cylinder head up and off the lower section. Note the integral camshaft bearing caps in the casting 90953p82.jpg
prev.gif next.gif

Jan 29, 2011 | 1999 Volvo S70

1 Answer

How change head light


open bonnett look behind the head lits may be hidden is wires going to the head light and a cover protecting the head light just take out this and replace the new one. hope this helps.

Feb 22, 2010 | 2002 Kia Optima

1 Answer

How do I replace headlight switch in my 95 Pontiac Bonneville


assuming that u have replaced any bad fuses. you have to remove the cover around the instrument panel. then u need to have a socket small enough to remove the screws that hold the head light switch in place. the head light switch knob should come out. you may have to pull it out first before u take the cover off. then remove the old switch and disconect the wires then replace the switch. i hope this helps

Oct 03, 2009 | 1995 Pontiac Bonneville

1 Answer

How to replace the front light bulb in my malibu do you need tools for this


screw off the cover of the head light until it reach the head light then screw of the head light to be place out to the car then open the head light then replace the the light.

Jul 22, 2009 | Chevrolet Malibu Cars & Trucks

1 Answer

Back Up light bulb replacement


Sounds like you have Torx head screws. You should be able to buy an inexpensive torx screw driver set to take care of the access problem.

Mar 21, 2009 | 1992 Chevrolet Cavalier

1 Answer

Headlight prices mercery sable


at ezbodyparts.com a head lite with bulb is 101 dollars

Jan 13, 2009 | 2001 Mercury Sable

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...