Question about 1998 Hyundai Elantra

1 Answer

Air bag lit on

Air bag indicator is always on

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

If the light is continuosly lit that indicates a fault in the SRS system have it checked by a shop you trust or the dealer

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is 'check air bag' indicator on?


The air bag indicator is lit as the result of a error found during the internal diagnostics by the SRS computer.

It is likely that the Air Bag system has been disabled when the light is lit a concerning issue that needs to be addressed.

Your friendly auto parts stores are usually willing to perform a complementary OBDII diagnosis reading the error codes set by the SRS supplementary restraint System. Many cases an estimate of the repair cost can be determined from the fault code.

Extreme caution is required when servicing components of the SRS system because of the explosive charge. Qualified service technicians are required to service.

Typical error codes.

26147897-f1dbbl4o5m3nghfc10hihvyr-4-0.jpg Hope this has helped?

Mar 31, 2016 | Renault SCENIC Cars & Trucks

1 Answer

Where is passenger side air bag relay 2007 MKZ


There is no relay for the passenger side air bag . What seams to be the trouble ? There is possibly a code set in the air bag control module .
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants, in addition to that provided by the 3-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles are also equipped with driver and front passenger safety belt retractor pretensioners. These vehicles can also be equipped with optional side air curtains that deploy from the A-pillar to the C-pillar upon a side impact. Vehicles with optional side air curtains are also equipped with seat side air bag modules in the front seats.
Side air curtains deploy from the headliner, protecting the first and second row outboard occupants during a side impact. Seat side air bag modules deploy from the outboard front seat backrest upon a side impact. In addition, a front impact severity sensor is mounted to the lower radiator support, a seat position sensor is mounted to the driver seat and a usage detection switch is added to the front driver and passenger outboard buckles. If equipped with optional side air curtain modules and seat side air bag modules, there are an additional 4 side impact sensors.
Vehicles are also equipped with an occupant classification sensor (OCS) system as part of the front passenger seat. The OCS system includes 2 OCS rails and an OCS module.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty and passenger safety belt buckle unbuckled, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.
When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants correct functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0 to 1.5 seconds of a change of state from the OCS system.
When an OCS system fault is present, the RCM defaults the passenger air bag module to the last valid state received from the OCS system until the ignition switch is turned OFF. If the OCS system fault is still present when the ignition switch is turned ON, the RCM defaults the passenger air bag module to enabled regardless of the size of occupant in the front passenger seat. The PAD indicator will be unlit. For information on the OCS system, refer to Occupant Classification Sensor System in this section.
The following table indicates the passenger air bag status and the PAD indicator status based the size of the front outboard passenger occupant.

Oct 04, 2015 | 2007 Lincoln MKZ

1 Answer

Flashing check engine light, lit air bag light, code p0306 and p0306pd


PO306 is a miss on cylinder #6. More than likely a bad plug or plug wire. But can also be a bad fuel injector or coil if this engine is a coil-on-plug design. PO306pd I have never head of. Air bag light lit normally indicates a problem with the SRS. This is a system that should only be repaired by a professional due to the hazards of working on this system.

Feb 28, 2011 | 1997 Chevrolet Suburban

1 Answer

Where is the switch to disable the passenger airbag on a 2003 ford taurus


Supplemental Restraint System (SRS) Depowering and Repowering

Depowering Procedure

WARNING: Always wear safety glasses when repairing an air bag supplemental

restraint system (SF3) vehicle and when handling an air bag module. This will reduce

the risk of injury in the event of an accidental deployment.

WARNING: Never probe the connectors on the airbag module. Doing so can result in

air bag deployment, which can result in personal injury.

WARNING: To reduce the risk of personal injury, do not use any memory saver

devices.

NOTE: Ifa seat equipped with a seat mounted side airbag and or a safety belt

pretensioner (if equipped) system is being serviced, the supplemental restraint system

(SES) must be depowered.

NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the

ignition switch is ON. This is normal operation and does not indicate a supplemental

restraint system (SRS) fault.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle

to the customer

1. Turn all vehicle accessories OFF.

2. Turn the ignition switch to OFF.

3. At the central junction box (Cm), located below the LH side of the instrument panel,

remove the cover and the restraints control module (RCM) fuse F223 (lOA) from

the CTh. For additional information, refer to the Wiring Diagram Manual.

4. Turn the ignition ON and visually monitor the air bag indicator for at least 30

seconds. The air bag indicator will remain lit continuously (no flashing) if the correct

ROsI fuse has been removed, If the air bag indicator does not remain lit

continuously, remove the correct RCM fuse before proceeding

5. Turn the ignition switch to OFF.

6. WARNING: To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any front or

side air bag supplemental restraint system (SRS) components and before set-ricing,

replacing, adjusting or striking components near the front or side air bag sensors,

such as doors, instrument panel, console, door latches, strikers, seats and hood

latches.

To deplete the backup power supply energy, disconnect the battery ground cable

and wait at least one minute. Be sure to disconnect auxiliary batteries and power

supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.

Repoweri.ng Procedure

1. WARNING: The restraint system diagnostic tool is for restraint system service

only. Remove from vehicle prior to road use. Failure to remove could result in

injury and possible violation of vehicle safety standards.

Make sure all restraint system diagnostic tool(s) that may have been installed during

the repair have been removed from the vehicle and all SRS components are

connected.

2. Turn the ignition switch from OFF to ON.

3. Install the ROsI fuse F2.23 (lOA) to the DB and install the cover.

4. WARNING: Be sure that nobody is in the vehicle and that there is nothing

blocking or set in front of any air bag module when the battery ground cable is

connected.

Connect the battery ground cable.

5. Prove out the supplemental restraint system (SRS) as follows:

Turn the ignition key from ON to OFF. Wait 10 seconds, then turn the key back to

ON and visually monitor the air bag indicator with the air bag modules installed. The

air bag indicator will light continuously for approximately six seconds and then turn

off. If an air bag supplemental restraint system (SF3) fault is present, the air bag

indicator will:

- failto light.

- remain lit continuously.

- flash.

The flashing might not occur until approximately 30 seconds after the ignition switch

has been turned from the OFF to the ON position. This is the time required for the

restraints control module (RCM) to complete the testing of the SRS. if the air bag

indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5

sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered

must be diagnosed and repaired.

Jan 12, 2011 | 2003 Ford Taurus

1 Answer

03 ford f250 quad cab 4x4 the PAD switch appears to be faulty and maybe the PAD off light the blink codes are 2 5 i have tried to jiggle the key in the PAD lock and have gone off and on several times...


refer to Passenger Air Bag Deactivation Indicator in this section.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system and the passenger air bag deactivation (PAD) switch. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants proper functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0+0.5 seconds of a change of state from the OCS system or PAD switch.When an OCS system fault is present the SRS defaults the passenger air bag module to enabled regardless of the PAD switch status or the size of the occupant in the front outboard passenger seat. The PAD indicator will be unlit. The cost of PAD SWITCH is near to $85. and yes it’s a dealers part/but some car parts store keeps the compatible PAD SWITCH parts with them.they are not original but compatible.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 02, 2010 | Ford F-250 Cars & Trucks

1 Answer

Hello I saw the break alert light lit on my


Usually when th fluid level low light comes on, it is because the fluid is ging to the front calipers to fill the pistons that push the brake pads against the rotors. This is because the pads are worn down and probably need replacing.

As for the 3 beeps, it is not related to the brakes.

if it is 5 beeps, it is the air bag or pretensioner.

When the ignition is cycled (turned off and then on), the air bag indicator will remain lit for six seconds and then go out. If an SRS fault exists, the air bag indicator will then flash the two-digit LFC. The air bag indicator will flash the LFC five times, then it will remain illuminated for the rest of the key cycle. The RCM will also communicate the current and historical DTCs through the data link connector (DLC), using the scan tool. If the air bag indicator does not function, and the system detects a fault condition, the RCM will signal the GEM to activate an audible chime. The chime is a series of five sets of five tone bursts. If the chime is heard, the SRS and the air bag indicator require repair.

Mar 02, 2010 | 2002 Ford Ranger Regular Cab

1 Answer

Airbag light flashes 1-8, stays lit


You have a bad Passenger Air Bag Deactivation Indicator. The bulb that shows when the passenger air bag is off.
Have seen alot of these go bad especially in police cars. The part number you need is 5W1Z-10A936-A.

Apr 15, 2009 | 2005 Ford Crown Victoria

2 Answers

Air bag Indicator flashed and than stays on


If the only code 52 is flashing then system is ok and just needs to be cleared.Look behind the glove box and find the gray 2 wire connector.It will be on the left side behind the glove box and follow the proceedure below. Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ±two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic Service Connector located underneath the glove compartment containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (T/R) to Circuit 57 (BK). Diagnostic trouble code is now cleared from NVM. Next highest priority diagnostic trouble code stored in NVM (if one exists) will begin flashing

Mar 03, 2009 | 1994 Ford Mustang

1 Answer

VW Golf Mk 5 + Air bag indicator


you may have a loose connection somewhere,if you plug into a diagnostic reader it will tell you where problem is.

Feb 22, 2009 | 2005 Volkswagen Golf

1 Answer

1999 f150 airbag light stays on after blinking upon start up!


Passenger Air Bag Deactivation (PAD) Switch
The passenger air bag deactivation (PAD) switch:
  • is located on the instrument panel to the right of the climate controls.
  • contains a light emitting diode (LED) that indicates when the PAD switch is activated (passenger air bag disabled).
  • allows the passenger air bag deployment circuit to be disabled using the ignition key.
  • should be used whenever a child safety seat is being used in the front passenger seating position.
------------------------------------------------------------------------------------------
Prove Out the System
Prove out the system means to turn the ignition switch from the OFF to the RUN position and visually monitor the air bag indicator with the air bag modules installed. The air bag indicator will light continuously for approximately six seconds and then turn off. If an air bag supplemental restraint system (SRS) fault is present, the air bag indicator will either:
  • fail to light.
  • remain lit continuously.
  • flash.
The flashing might not occur until approximately 30 seconds after the ignition switch has been turned from the OFF to the RUN position. This is the time required for the restraints control module (RCM) to complete the testing of the SRS. If the air bag indicator is inoperative and an SRS fault exists, a chime will sound in a pattern of five sets of five tone bursts. If this occurs, the air bag indicator will need to be repaired before diagnosis can continue.
----------------------------------------------------------------------------------------
Active Commands
This command allows the technician to verify operation of the air bag indicator, passenger air bag deactivation (PAD) lamp and chime. When the air bag output command is executed, the indicator, the PAD lamp, chime and the chime are activated simultaneously for approximately four seconds. All devices are deactivated automatically.

Jan 15, 2009 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Hyundai Elantra Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...