Question about 2007 GMC Yukon

1 Answer

Its a 1989 ford crown victoria and i was wondering how to fix my park,reverse,drive,...etc. gauge it shifts and all but the needle wont can some one tell me how to fix this problem please.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

If the lever is mounted on the steering column then the wire is probably broken you will need to dissambly the column to do that.

Posted on Apr 26, 2010

Testimonial: "thanks "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 ford crown victoria wont come out of park


Check your brake lights, if they don\'t work the interlocking system will not let you shift from park. If brake lights don\'t work probably the brake lamp switch on the pedal shaft. Check power in and out of switch when stepping on pedal, if nothing coming out, swi

May 25, 2014 | 1999 Ford Crown Victoria

2 Answers

1989 Ford Crown Victoria wont go into reverse and drives in nuetral???


Sounds like your linkage slipped out of sequence. On your transmission there is a place where you can manually shift your tansmission through the gears. When you move the selector on the trani it should move the shifter as well. All the way up on selector should be park, then R,N,D so on. If you move the selector all the way up at your shifter reads something else, you need to adjust the linkage and put car in park with selector on trani in park and tighten linkage back up. Run through all the gears and you should be good.

90345b2e-83af-476b-ab39-dd6e70c72847.jpg

Apr 14, 2013 | 1989 Ford Crown Victoria

1 Answer

Crown victoria 1989 kick down assembly


There a tab at the linkage you unlock it and slid the cable till it is just a little loose the snap the tab back in, drive the car and make a note when the car shifts into overdrive, it should do it at about 55 miles per hour at half throttle, if it shifts to fast tighten the cable if it stays out of overdrive loosen it

Aug 22, 2012 | Ford Cars & Trucks

1 Answer

2000 Ford Crown Victoria transmission want shift into drive but have reverse


check pressures for drive gears if not in range then possable bad clutches in the ****** if you have a scan tool scan for shift coads and tern your shift sylinoids on and off to see if you have engagement if not rebuild or replace

Jul 22, 2012 | 2000 Ford Crown Victoria

2 Answers

I have a 93 crown victoria and it runs great but more often when I put it into park it doesnt want to start again. I have to reput it in park 3 or 4 times.


Bad PRNDL switch(park/reverse/neutral/drive/low).May be adjustable,but most likely the switch is bad.As a temporary/free solution,try starting in Neutral(USE YOUR PARKING BRAKE!)

Mar 14, 2012 | 1993 Ford Crown Victoria

1 Answer

1995 crown vic gear problems/gear shift wont lock


most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

May 30, 2009 | 1995 Ford Crown Victoria

1 Answer

Tail lights not working while drive. brake,blinkers work


i have a crown victoria with brake lights no tail lights could you help me?

Nov 19, 2008 | 1989 Ford Crown Victoria

Not finding what you are looking for?
2007 GMC Yukon Logo

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...