Question about Isuzu Rodeo

1 Answer

System is charged. Compressor on only when jump the relay.2 poles have 12V the relay has been replaced. A/C control lamp is lit and all fuses are good. Found that the heater relay supplies 12V to the a/c relay.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Isuzu Master
  • 1,348 Answers

There is a pressure switch that tells that the system is charged.that turns on the relay.it is best to get the wiring diagram for it.

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse for the alarm system


Here is the full list of fuses for you! and for the car.

Fuses on E-box, on left in Engine Compartment

Fuse 1 - Not assigned

Fuse 2 - 10/15A - Engine control unit

Fuse 3 - 5A - Radiator fan control unit

Fuse 4 - 5/10/15A - Lambda probe heater,
Lambda probe 1 heater after
catalytic converter

Fuse 5 - 10A, 20A - Lambda probe heater1,
Lambda probe 1 heater after
catalytic converter,
Fuel system diagnostic pump,
Charge pressure control solenoid
valve,
Exhaust gas recirculation cooler
change-over valve,
Crankcase breather heater element,
Vacuum pump for brakes

Fuse 6 - 5A, 10A,15A - Fuel system diagnostic pump,
Throttle valve module,
Activated charcoal filter system
solenoid valve 1,
Continued coolant circulation pump,
Auxiliary air heater heating element

Fuse 7 - 20A, 5A - Ignition transformer,
Fuel pressure regulating valve,
Fuel metering valve

Fuse 8 - 10A - Throttle valve module,
Activated charcoal filter system
solenoid valve 1

Fuse 9 - 5A - Automatic glow period control unit,
Electric fuel pump 2 relay,
Fuel pump relay

Fuse 10 - 5A - Speedometer sender,
Brake light switch

Fuse 11 - Not assigned

Fuse 12 - 5A - Coolant circulation pump

Fuse 13 - 5A - Water pump

Fuse 14 - 5A - Engine control unit

Fuse 15 - 30A - Voltage stabiliser

Fuse 16 - 30A - ABS control unit

Fuse 17 - 30A - Automatic gearbox control unit

Fuse 18 - 20A - Automatic gearbox control unit

Fuse 19 - 1A - Onboard supply control unit

Fuse 20 - 30A - Onboard supply control unit (AW0)
Automatic intermittent wash and
wipe relay (AW1)

Fuse 21 - 50A - Secondary air pump motor

Fuse 22 - Not assigned

Fuse 23 - 40A - ABS control unit

Fuse 24 - 50A - Trailer detector control unit

Fuse 25 - 50A - Terminal 15 voltage supply relay 2

Fuse 26 - 60A - Automatic glow period control unit

Fuse 27 - 60A - Radiator fan

Fuse 28 - 40A - Onboard supply control unit (AW1)

Fuse 29 - 40A - Onboard supply control unit (AW1)

Fuse 30 - 50A - Terminal 75 voltage supply relay 1

Fuse 31 - 30A - Amplifier

Fuse 32 - Not assigned

**************************************************

Fuse assignment - Interior Fuse Panel

Fuse 1 - Not used

Fuse 2 - 5A - Electronic steering column lock control module

Fuse 3 - 10A - Instrument cluster control module

Fuse 4 - Not used

Fuse 5 - Not used

Fuse 6 - 10A - Vehicle electrical system control module,
Interior ceiling lights,
Tail lights

Fuse 7 - 5A - Fog lamp relay,
Instrument panel and switch illumination dimmer switch,
License plate lamps,
Vehicle electrical system control module

Fuse 8 - 7.5A - Windshield and headlamp washer pump switch,
Windshield washer pump

Fuse 9 - 5A - Airbag control module

Fuse 10 - 10A - Right steering column switch

Fuse 11 - Not used

Fuse 12 - Not used

Fuse 13 - 5A - Automatic dimming interior rearview mirror,
Light recognition sensor,
Parking aid control module,
Air quality sensor,
High pressure sensor,
Climatronic control unit,
Tire pressure monitoring button,
Back-up lamp switch,
Left washer nozzle heater,
Right washer nozzle heater,
28-pin connector

Fuse 14 4- 10A - Left steering column switch,
ABS control module,
Light switch,
Airbag spiral spring/return spring with slip ring,
Fuel pump control module,
Data bus on board diagnostic interface

Fuse 15 - 10A - 16-pin connector (diagnostic connector),
Instrument panel and switch illumination dimmer switch,
Headlamp range control adjuster,
Auxiliary heater operation relay,
Mass airflow sensor,
Positive crankcase ventilation heating element,
Left front headlamp,
Left headlamp beam adjustment motor,
Right front headlamp,
Right headlamp beam adjustment motor,

Fuse 16 - 10A - Engine control module

Fuse 17 - Not used

Fuse 18 - 15A - Left front headlamp

Fuse 19 - 15A - Right front headlamp

Fuse 20 - 10A - Automatic transmission control module,
Selector lever sensor system control module,
Tiptronic switch,
Climatronic control unit,
Ignition/starter switch

Fuse 21 - Not used

Fuse 22 - 10A - Ignition/starter switch,
Converter box,
Alarm horn,
Interior monitoring sensor,
Alarm horn relay,
Dual tone horn relay

Fuse 23 - 10A - Vehicle electrical system control module,
16-pin connector (diagnostic connector),
Light switch,
Rain/light recognition sensor,
Compass magnetic field sensor,

Fuse 24 - 10A - Vehicle electrical system control module,
Access/start authorization control module

Fuse 25 - 15A - Automatic transmission control module,
Selector lever sensor system control module,
Multifunction transmission range switch

Fuse 26 - 15A - Brake system vacuum pump

Fuse 27 - Not used

Fuse 28 - 40A - Auxiliary heater operation relay

Fuse 29 - 1A - Vehicle electrical system control module,

Fuse 30 - 20A - Cigarette lighter,
12 V socket,
12 V socket 2,
Blocking diode

Fuse 31 - 30A - Light switch

Fuse 32 - 20A - Light switch

Fuse 33 - 40A - Heater/heat output switch,
Fresh air blower relay,
A/C control module,
Fresh air blower switch

Fuse 34 - 15A - Left front headlamp,
Left front headlamp,
Instrument cluster control module

Fuse 35 - 10A - Steering column electronics control module,
Instrument cluster control module,
Signal horn activation,
Data bus on board diagnostic interface

Fuse 36 - 25A - Vehicle electrical system control module

Fuse 37 - 15A - Left front headlamp DRL

Fuse 38 - 15A - Right front headlamp DRL

Fuse 39 - 15A - Low beam relay

Fuse 40 - 15A - Towing recognition control module

Fuse 41 - 15A - Towing recognition control module

Fuse 42 - 20A - Towing recognition control module

Fuse 43 - 30A - Front passenger door control module

Fuse 44 - A25 - Rear window defogger relay,
Vehicle electrical system control module

Fuse 45 - 30A - Driver door control module,
Front passenger door control module

Fuse 46 - 30A - Left rear door control module,
Right rear door control module

Fuse 47 - 15A - Fuel pump control module,
Fuel pump relay,
Fuel primer relay

Fuse 48 - 20A - Vehicle electrical system control module,
Vehicle electrical system control module,
Vehicle electrical system control module,

Fuse 49 - 20A - Climatronic control unit,
A/C control module

Fuse 50 - 30A - Front seat heating control module

Fuse 51 - 30A - Power sunroof control module

Fuse 52 - 20A - Dual tone horn relay

Fuse 53 - 15A - Front seat heating control module

Fuse 54 - 15A - Fog lamp relay

Fuse 55 - 20A - Light switch,
Left steering column switch

Fuse 56 - Not used

Fuse 57 - 15A - Radio,
Radio/navigation display unit control module

Fuse 58 - 1A, 30A - Telephone transceiver
DC/AC converter with socket, 12V-230V

Fuse 59 - 30A - Amplifier

Fuse 60 - 30A - Auxiliary heater control module


Hope this helps

--N

May 31, 2014 | 2010 Volkswagen Jetta

1 Answer

Right side parking lights


usa car, not Renegade or export car. nor DRL lamps.

fuse, can look good but be bad.
use any ohm meter, to make sure they are good. 0 ohms good.
the car can have park-tail relay. yes, it does have a park relay
that feeds 2 fuses (#7&9) then all lamps left and right.
the BCM controls the relay. body brain.

check voltage at all 4 pins of park relay, and bingo know who is messing up,?
pins 86/87 hot 12v all the time( battery)
87a = ground 0v all times.
30 is relay output, 12v park on.
85 pin is relay coil control. 0v park, 12v not park.
if you have 0v on 85 , in park the BCM is working

there is start.
if a fuse is blown to the BCM, it will mess up

Jan 06, 2014 | 2004 Jeep Liberty

1 Answer

HOW TO FIND OUT IF A/C PRESSURE SWITCH IS BAD


Probably the high pressure switch on the accumulator - try disconnecting the connector and jumping the pins to see if the clutch will engage. If that is the problem, DO NOT leave it jumped - replace the switch.
If that is not the problem, you will have to check the clutch wiring, relay and fuse for continuity back to the HVAC controls. If that is OK, the problem will probably be in your HVAC control module.

Oct 14, 2017 | 1996 GMC Sierra

1 Answer

New compresser just stopped working was very cold ran it all day and now the compressor is not kicking in and out how can you tell if it is a relay or loss of carge


FIrst, with any electrical problem, always check the fuses first. The only way to correctly check the charge of the AC system is with a set of guages. You can assume the charge is good and procede with the electrical diagnosis, but it may all be a waste of time if the system has lost the charge. With the AC on, if there is a proper charge in the system, there should be 12v at the compressor clutch connector. This will be a 2 wire connector just behind the AC pulley. You will need a 12v test light, meter, or some way to check for voltage. If there is 12v and the compressor is not engaged, then the clutch coil has gone bad. If there is not 12v then you will need to check the relay for voltage. Sometimes you can swap relays with another that has the same part number. If the original relay is bad then the compressor will start working after the swap. Check all the fuses, under the hood and under the dash. Sometimes a fuse will control more than one circuit.

Jul 30, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Jumped the relay and compressor came on and system charged it was blowing cold. When I put relay back in the compressor will not come on. I swapped relays and still nothing. But every time I jump it it...


So the relay coil is not being energized. You will need to determine why. It could be the ground signal from the PCM, which is effected by the control panel A/C switch or else it is the positive signal from the 10 amp CRUISE fuse, which must pass thru the pressure switches (high and low). First check the fuse. If the fuse is good, use a 12 volt test light to probe the relay socket to see which signal is not getting to the relay. Connect your test light clip to chassis ground, start the car, turn the A/C on, and probe the relay socket. There should be 2 hot terminals in the socket--one from the 10 amp compressor fuse, which you have been using to power the clutch, and one from the pressure switches. If you don't get this second hot terminal, try jumping each pressure switch connector one at a time to see which one is not closing. If you DO get both hot signals, the problem is the signal from the PCM. Move your test light clip to battery positive and probe the relay socket again. If the negative signal is absent from the relay socket, only the clutch terminal will show any voltage. If this is the case, you will first need to check the continuity of the wire (dark green with a white stripe) from the PMC connector 2 pin 47 to the relay socket. If the wire is good, the problem may be in the control panel. If you get this far and/or you get stuck along the way, please get back to me.

jturcotte_1963.gif

Jul 24, 2011 | 2001 Cadillac DeVille

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

1 Answer

I want to wire 2 driving lamps into my discovery


Instal a relay (preferably in a mounting socket); Wire one side of the control coil to the +12v mainbeam 'on' circuit.
Take the other relay coil control connection to the additional 'Driving-lamp on' control switch (switched to ground).
Supply relay contacts 'common' with a fused +12V from battery - use wire with sufficient current carry capacity to feed driving lights. Connect switched +12V output to the driving lamps.

Oct 27, 2009 | 1998 Land Rover Discovery

3 Answers

A/C Compressor not kicking on


The power to run the compressor clutch coil goes from the battery, to the AC Clutch Relay, somewere in the engine compartment fuse box, then it goes to the positive side of the AC compressor clutch coil; goes thru the coil, activating the compressor, and then goes to complete the circuit through another switch (high pressure protection switch) in the back of the AC compressor and finally reaching negative or Ground.

Disconnect the AC compressor clutch connector and using a 12 V bulb with 2 wires (test lamp) check the following:

1.- connect 1 lamp wire to battery neg; with the other check both pins at connector with the AC in the RUN (AC and ignition switch on ) you should have power in one side.

2.- connect 1 lamp wire to battery positive and with the other check both pins at connector, lamp should light getting the ground from the clutch connector thru the high pressure compressor switch to ground.

On the other side what makes the relay close and let the power flow to the clutch works with the low pressure switch, (if the freon pressure is too low it opens and kills the ground to the relay coil and that kills the compressor), that low pressure switch is in the low pressure side of the freon tubing, the fat pipe that comes from inside the firewall into the accumulator/dryer, a big aluminum cylinder sitting on the right side of the engine compartment in GM cars.

To know if the low press switch is the cause you can unplug it and connect both legs with a paper clip for a minute or two, no more, you don't want to damage the compressor. anyway if jumping the switch makes the compressor come alive and kick in, you either have low freon pressure or a bad switch; it's time for the pressure gauges and check how the compressor is pumping and that is better left to a pro.

By the way you said that your system is a R-12 system, have you considered switching to R-134a the new "ozone friendly" freon? to do that you need to evacuate the system with a recycling machine and pull vacuum in your AC, if it holds the vacuum for a while, then you can be sure that there are not leaks and then dump 1.5 or 2 pound (check the labels in the engine compartment) of R-134a into your system. it will be a good idea to put some fluorescent leak detecting dye in the system to check for leaks, just in case..

Jun 13, 2009 | 1992 Oldsmobile 88

1 Answer

2000 Buick LaSabre A/C compressor replaced. The new compressor


Defective AC fuse, relay, pressure switch (low/open), intermittent compressor wiring (check connections and harness), bad control module/switches.

Apr 11, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...