Question about 1997 Isuzu Rodeo

1 Answer

When key is turned clicks once does not turn over changed starter same problem can push and pop clutch runs fine battery ok

Posted by on

  • cinci124 Apr 26, 2010

    Fixed it was not the clutch switch because it clicked one time that means the safety switch was not preventing it from working so it had to be wiring checked all grounds and finaly found a spot in positive battery cable that had worn through and cable was nearly gone was enough to power radio but not starter

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

Check the clutch switch it prevents the starter from turning the engine if the clutch pedal is not depressed

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi eclipse starter


clutch sensor at the clutch pedal

Aug 05, 2013 | Cars & Trucks

1 Answer

Engine wont turn over and start


Bad ignition switch not the key switch the ignition switch i would check that first.Then the key switch.

Dec 12, 2012 | 1992 Mitsubishi Mighty Max

1 Answer

88 rx7 run but wont start


The FC3S is notorious for this and fueling issues. Check all ground points, battery cables and connections. Check the draw from the starter. If the voltage drops below 10V there is not enough power for the ignition, causing weak spark. It really needs to spin over 200rpm cranking. Pop starting does not necessarily mean the compression is good. You need to make sure it cranks fast enough to get a proper compression test with rotary tester, New NGK plugs, new NGK plug wires.

May 28, 2012 | 1988 Mazda RX-7

1 Answer

How can I bypass the starter in my car(manual trans) so it will start? I had the battery checked and it's fine.


  • If the engine cranks ("rrr-rrr-rrr") when you turn the key, then the problem isn't the starter or the battery.Plan to have at least one person sitting in the driver's seat and one or two persons pushing.Turn off all accessories (radio, wipers, lamps).Turn the key to the "on" position.Depress the clutch pedal with your foot.Put the transmission in first or second gear.Release the hand brake and the foot brake.Note that the people pushing need to get the car rolling as fast as they can. This works best down a hill or an incline.Release the clutch pedal while giving the engine a little gas with the gas pedal once the car is moving about as fast as you can run. The engine should start

  • Jan 12, 2011 | 2004 Acura TL

    2 Answers

    I have a 2000 ford focus with a manual transmition and zetec motor I turn the key and everything lights up but the engine doesnt turn I had it push started and it ran fine I changed the starter and it...


    Check for bad grounds, start with the starter ground. Do you even get a click when trying to start? If not then the starter is getting no power and check your hot lead to the starter also. Make sure the battery terminals are cleaned well.

    Nov 16, 2010 | 2000 Ford Focus

    2 Answers

    2001 Dodge Ram 1500 5.2 Battery died and Replaced also Starter still no start just loud click from new starter and does not turn over engine but can be push started by pop clutch and runs fine


    Assuming you replaced the solenoid with the starter, it may be the relay. If the relay is not making a good connection, it might have trouble throwing the solenoid. The relay should be in the relay box under the hood. You can break the relay open and watch it work while someone turns the key to verify the problem.

    Sep 20, 2010 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    Pickup wont start


    You didn't give me a lot to go on but I'll try. First make sure the battery has a good charge. If the head lights come on and all the electrical items power up than the battery terminals should be ok. If not or the lights dim badly when you try to key start clean the battery terminals. If it still will not crank, (turn over,) than it is more than likely the starter. Good luck.

    May 12, 2009 | 1989 Toyota Pickup SR5

    1 Answer

    My jeep won't start (1987 Jeep Cherokee)


    Your starter needs a "makeover". try to clean or change the brushes in the starter.

    a cheap and simple solution, is to make the cables on the starter longer, and attach them to a button in you car. If you choose that solution, you just have to turn on the ignition, and then push the button you have connected the starter cables to.

    Apr 11, 2009 | 1987 Jeep Cherokee

    Not finding what you are looking for?
    1997 Isuzu Rodeo Logo

    Related Topics:

    168 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...