Question about 1991 Chevrolet Camaro

1 Answer

Will the engine cradle from a 91 comaro fit my 86, evrything but the t-tops looks like it would fit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

I would call a Chevy parts department and check if the part numbers are the same. Too many variants these days to guess at this one

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Minnie winnie


gas or diesel ? if its gas find shrader valve (tire valve looking thing) on injector fuel manafold top of engine tap key on/off several times depress center of valve with plastic point nothing metal (old ink pen?) look for fuel to briefly spray out a bit (shield eye's) no fuel ck fuel pump , filter and inertia switch ,yes fuel ck all the sensors the injectors are not firing
Diesel ? A 86 would be A IdI type so loosen fuel fitting(one turn) to top of # 4 injector (you can't reach others) Do not remove it (High pressure!!!) crank engine several times over look for fuel leak at fitting thats loose ,it might even start if injector pump was airlocked that happens alot from sitting ,if it does don't get your body near loose fitting(high pressure) too dangerous shut off key and tighten fitting then restart engine

Nov 06, 2013 | 1986 Ford F 350

1 Answer

How can I tell if my engine is the orginal I had


There is a letter and 6 digit number stamped on the top of the front housing. There is a flat inboard of the distributor on pre1986 7's SA/FB. or the eccentric shaft sensor 86/91 FC3S. On the FD3S 93 it is the same flat just this side of the front engine mount when looking at the engine from left side. The six digit number should match the VIN of the car.

Oct 23, 2013 | 1988 Mazda RX-7

1 Answer

Whats the part number for a 95 camry timing belt is it 94167 (163stp8m267) thanks for ya assitance


3.0 Liter V6 engine use Dayco 95257
2.2 Liter 4 cyc engine use Dayco 95199

======== 94167 is an old Deyco Euro part #
It will fit the following
Toyota Camry 2.0 i 1996 3S-FE Petrol 10/86-06/91


Toyota Camry 2.0 i 16V 1998 3S-FE Petrol 10/86-06/91


Toyota Camry 2.2 i 16V 2164 5S-FE Petrol 06/91-07/01


Toyota Carina E 2.0 i 16V 1998 3S-FE Petrol 02/92-10/97


Toyota Carina E 2.0 i 16V 1998 3S-FE Petrol 02/92-10/97


Jul 31, 2011 | Toyota Camry Cars & Trucks

1 Answer

Head bolt torque nissan altima 1995 2.4l


  1. Tighten head bolts using the following procedure:
  2. Tighten all bolts to 22 ftlbs.
  3. Tighten all bolts 59 ftlbs .
  4. Loosen all the bolts completely.
  5. Tighten all bolts 18 to 25 ftlbs .
  6. Turn all bolts 86 to 91 degrees.If an angle wrench is not available, mark all cylinder head bolts on the side facing the engine front. Then, turn each cylinder head bolt 86 to 91 degrees.
There you are as asked for.
Thank you for using FixYA
KL

Mar 05, 2011 | 1995 Nissan Altima

1 Answer

I have a 99 K1500 Suburban with a weak 4l60e trans. I have a 97 Suburban 4l60e trans available. Will they interchange?


yes. 96-99 are the same. 95 are different. 94-88 are the same. thats the most i can tell you off the top of my head. As long as the trannis are the same type they'll fit. For example a 700r4 from an 86 will fit into a 88 with a minor adjustment. But an 86 700r4 will not fit into a 86 that had a TH-400 without major changes. So as long as they're both 4L60E within the years mentioned above they'll interchange just fine.

Jun 06, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

Looking to pull the engine out of 95 camaro 3.4 with manual tranny does it come out the bottom or the top?


You can pull that engine out of the top. It is easier to drop the engine cradle, remove the drive shaft firs, and wiring harness. There should be four bolts located on the cradle at four locations. Lower the cradle with 2 jacks one on each side, lift the car and slide cradle from under the car. i have done this with an Intrige and was easier than trying to pull from the top.

Jan 02, 2010 | 1995 Chevrolet Camaro

1 Answer

How and where to find the 2nd bolt on a 91 oldsmobile cutless ciera starter


one shouldbe right above the engine cradle and the other look between the cradle and the transmission

Oct 23, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

I have 1994 350 K engine in my '86 S10 Blazer. How do you route the heater hoses off the firewall (2 fittings)? Thanks I found 1 fitting on the top of the water pump. I am still missing 1.


the return hose connection could be at different locations on the block.put a garden hose to the water pump fitting & turn it on,you'll soon see it!!

Sep 24, 2009 | 1994 Chevrolet C1500

1 Answer

1989 Honda Civic hard starting and dies for no reason. Cooling fans not working. Trouble codes are #6 coolant, #10 air intake temp, #16 fuel injector. Can anyone lead me to a solution for these problems?


6
Accord Civic CRV CRX Del Sol Odyssey Prelude
85-98 86-98 97-98 85-91 93-97 95-98 85-98 ECT Sensor (Engine Coolant Temperature)
defective circuit or unplugged / defective sensor
10
Accord Civic CRV CRX Del Sol Odyssey Prelude
85-98 86-98 97-98 85-91 93-97 95-98 85-98 IAT Sensor (Intake Air Temperature)
defective circuit or unplugged / defective sensor
16
Accord Civic CRV CRX Del Sol Odyssey Prelude
90-95 88-95 n/a 88-91 93-95 95 88-95 Fuel Injector System
defective circuit or unplugged / defective fuel injector

check your wiring for dirty connections or broken wires, you may have wires that are rubbed through or connectors that are not making full contact. you will need an ohm meter and check wires for continuity. a wiring diagram will be needed.

May 15, 2009 | 1989 Honda Civic

1 Answer

B16A


The B16a will fit in the 86 as far as the positioning, and motor mounts go. Of course you will have to upgrade the ecu, or at least get a piggy back unit for the extra fuel to run that monster. Hope that helps. Oh yea, and I am pretty sure the tranny should fit, but you may want to check the codes/serial #'s at your local dealer.

Mar 12, 2009 | 1986 Honda Civic

Not finding what you are looking for?
1991 Chevrolet Camaro Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...