Question about 2000 Ford Expedition

1 Answer

Locate heater hose in a 2000 ford expedition - 2000 Ford Expedition

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Expedition and Navigator

locate heater hose in a 2000 ford expedition - b2302e3.jpg

Fig. 7 Remove the A/C plenum demister screw and remove the A/C plenum demister adapter

fe987d3.jpg

Fig. 8 Disconnect the vacuum line

468b3b9.jpg

Fig. 9 Remove the heater core bracket

a0086be.jpg

Fig. 10 Remove the 13 retaining screws and remove the plenum chamber top

7e3c78a.jpg

Fig. 11 Remove the heater core

  1. Disconnect the battery ground cable.
  2. Drain and recycle the engine coolant.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the instrument panel. Refer to .
  2. If equipped with the 5.4L 4V engine, remove the junction block splash shield.
  3. If equipped with the 5.4L 4V engine, remove the bolts and disconnect the cable ends from the starter relay.
  4. If equipped with the 5.4L 4V engine, remove the junction block bracket.
  5. Disconnect the heater core hose couplings.
  6. Remove the retaining screw and remove the A/C plenum demister adapter.
  7. Disconnect the vacuum line from the A/C plenum demister adapter.
  8. Remove the heater core bracket.
  9. Remove the 13 plenum chamber top retaining screws.
  10. Remove the plenum chamber top.
  11. Remove the blend door assembly from the case.
  12. Remove the heater core.To install:
  13. The installation is the reverse of the removal.
Also this VIDEO can help to solve your problem...

Hope this help.

Posted on Apr 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is vacuum canister located on a 2000 ford expedition suv


For exact location and diagram of vacuum canister on ford expedition,click the link below and view its diagram:----
Vacuum canister 2000 ford expedition

http://technoanswers.blogspot.com/2012/11/vacuum-canister-2000-ford-expedition.html

----------

These will help.

Thanks.

Nov 30, 2012 | Cars & Trucks

1 Answer

I have a 2000 ford expedition. what are the inner diameters of the heater hoses going thru the firewall


The hoses don't go through the firewall, they connect to the pipes of the heater core under the cowl in the engine compartment. The size should be marked on the outside of the hoses.

Mar 18, 2011 | 2000 Ford Expedition

1 Answer

I have a 2000 ford expedition and the heater blows air just not hot air or even warm air.. weve already changed out the thermostat, heater core, heater control valve and it still isnt working.. what could...


Check the vacuum hoses from the switch to the engine compartment. If you manually operate the heater valve on the firewall (follow the 5/8" hose) you will get heat.

Feb 08, 2011 | 2000 Ford Expedition

1 Answer

In a 2001 ford expedition when i connect the heater core hoses will my heater work better or will i get heat at all


if you have a good heater core and your hose are connected you should have heat if you just bought this and they were not connected your heater core may not be any good

Feb 03, 2011 | 2000 Ford Expedition

1 Answer

1998 Expedition: 2000 Ford Expedition I smell antifreeze with heate...


If you smell antifreeze it may be 3 possibilities: 1. you may have a leaking hose/hose connector , or water pump. 2. your heater core is bad and needs replaced. Unless you know what you are doing I would highly suggest taking to dealer for heater core replacement. The dash and steering colum has to be removed to get to the heater core. This is not an easy job believe me (about-900-1200 job). If you have your heater core replaced then also replace the climate control door. This is good preventative maintenance and also a a dollar saver. I would have a pressure check run on your radiator as a first thought. All you may have is a bad hose and that can easily be replaced.

May 18, 2010 | 1998 Ford Expedition

1 Answer

I cant locate my heater control valve, where is it???


The heater flow can be checked by feeling the hoses at the inlet and outlet to the heater core. If the heater has a control valve and it is open, both hoses should be warm. This indicates that coolant is flowing through the heater core. If the outlet hose is cold, there must be an obstruction in the heater core or control valve.
You can go to autozone.com and register for free for free online repair manual for your Ford

Oct 27, 2009 | 2000 Ford Expedition

1 Answer

Where is the heater core hose in my 2000 ford expedition?


check closer to just underneath the firewall--it could be a smaller problem than a heater core--Ford 4.6--5.4 engines have a tube just underneath the intake manifold that the rubber hose goes bad and it will leak towards the back of the engine.Lets hope so-what i hear its very expensive to change a heater core in an Expedition.

May 01, 2009 | 2000 Ford Expedition

1 Answer

The heater do not work in my 2001 ford expedition


sounds like your thermostat is not working (stuck closed). if the hose on top is soft after several minutes of engine running this is definitely the problem. good luck

Feb 21, 2009 | 2000 Ford Expedition

1 Answer

Heater not producing hot air


look between engine and heater core on heater hoses. It will be there on one hose or the other.

Dec 27, 2008 | 2000 Ford Expedition

1 Answer

2000 ford expedition


HI....
The heater on your Vehicle it can be a few problems.
I will mention the Importants.

First. Check the temperature, The temperature has to be At least 140 Farenheit.
Second. With a Temperature gace check the temperature of the 2 small hoses going to the Heater core. If the Temperature is almost the same on each of the small hoses, and Close to the temperature of the engine. The circulation is good.
But if only One of the hoses are Hot and the Other no. Is because is there a restriction in the Heater core, and will be nesesary to clean or replace.

Third.. Check the Blend door actuator motor. ( Is the actuator to move from cool to hot air )
Is located at center of the Instrument panel. at lower of the Hvac housing.
Is there behind the Center console.

Ok... Check the step I giving and letme know.
Thank you for use fixya...

Nov 20, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

618 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...