Question about 1995 Mercury Grand Marquis

1 Answer

Only drivers window works is there a fix think gears are bad for

Pulled pass door panel and can move window up and down by hand cable intact motor just makes clicking noise

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 61 Answers

Nylon gear inside regulator is gone or cable anchor is broken in either case you will have to replace. sugest dorman aftermarket.

Posted on Apr 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I fix drivers window that wont go up or down on a 2000 dodge durango

This is a common problem in these model years of Chrysler vehicles, Be patient and you can easily DIY. The mechanism consists of a motor and two cable/two guide rail assembly. The guide rails hold the window onto the cable with a clip on each rail. It is better to buy the whole assembly new rather than just replacing a bad motor or just the guide rail/cable assembly. I have been burned just replacing one or the other only to learn when popping open the cable spool that 1) cable is shredded or 2) it ain't easy winding the cable back up as tight as the mfr had it and the window won't roll up with the same speed as the other one. You will need a Torx set... a 25 or 30 size if I remember will remove the guide rail bolts. Some models have the motors riveting on with soft aluminum rivets. Just drill them out... like butter. Others have torx bolts on them with the nuts encapsulated inside a grommet. Put your hand behind and inside the door panel to hold them with your hand when removing the torx bolts. Their are two holes on the inside of the door panel... one guide rail is extracted through one of them, and the other one through it's own hole. Push the window up first, have an assistance hold it halfway up for you so you can see and pull the guide rail release clips with needle-nose pliers. Push the window up all the way and tape it using a good tape around the door sill at the top. Then you can start removing/replacing the motor and guide rails. When your done, plug the wiring harness back in and raise the guide rail half way up using the motor and then unplug the harness again. Have your trusty assistant lower the window down gently, insuring it's inside the groove and stopped by the guide rail clip assembly. Insert the clips back in and test your work before re-assembling your door panel. Crutchfield makes new door panel liner, if yours is crispy. A heat gun sometimes help remove them more intact. Good luck!

Oct 05, 2014 | 2000 Dodge Durango

1 Answer

Driver door window will not go up, motor is operating.

If you can hear the window motor running but the window does not move, the gears are stripped or the cable is broke depending on what type of regulator you have.
Someone will need to pull the door panel off and check the regulator.

Feb 14, 2013 | Dodge Ram 1500 Cars & Trucks

2 Answers

How do I fix my rear window it won't roll up ?

open the door, make sure the window is in its carrier, power cables conected to the motor and motor is working. This should savd u, good luck.

Jun 26, 2011 | 2006 Hyundai Sonata

1 Answer

My 1996 Ford explore xlt and my driver side window will not go up or down on its own. I can force it to roll down and pull/push it up with my hand. When I push the button to roll it up I can hear the...

The window may have come of the track, if you can hear the motor, it's probably fine. If the window moves around freely, it's most likely of track.

Apr 04, 2011 | 1996 Ford Explorer

1 Answer

Driver door window will not move. The motor makes

possible broken motor cable or motor gear that move your window up and down, need visual inspection...

Feb 03, 2010 | 1994 Toyota Camry

2 Answers

Drivers window (electric) cannot close it, l can hear the motor whirring when l press the down but nothing when l press the up.

Either your gears in the motor are bad or the drive cable that moves the window up and down is damaged. You need to pull the door panel to verify.

Aug 30, 2009 | Renault R18 Cars & Trucks

1 Answer

1996 monte carlo windows will not go down or up from drivers side master switch and pass side switch will only go down. I know both switches are good, I pulled them and put in 1995 monte and they work fine...

it's in the circuit relay in the drivers master control pannel switch inorder to opperate these windows you actually have to short the power to ground inorder to move the windows up or down you need to repair/ replace the switch,
I had beat myself to death with that problem ,spent all winter taking my door apart to open and repair the door when the window kept coming out of it's tracks,Nice cars but boy never owned a chev that had as many problems as this one everytime you think you have it fixed another problem sneaks up and kicks you in the ***,good luck bud..

Jul 07, 2009 | Chevrolet Monte Carlo Cars & Trucks

2 Answers

Hi I own a 1998 Jeep Cherokee and the driver's side window button stopped working(its stuck open). Neither rear windows will work at all, but the passenger window will go up and down with its own button....

Look for window relay on fuse box inside car or at motor compartment Once You find it switch it for another from a window that You know it works, if no thing happen, pull switch of the door, at main left door and by pass the wires, with an" U" shaped wire, see if works, if not, pull door panel off, brake nylon locate the window motor and tap it with hammer wile pressing switch going up, If is Your driver window,that's the first one to go bad

Jan 23, 2009 | 1998 Jeep Cherokee

1 Answer

Drivers window

Could be, but I doubt it.
More then likely, it has more to do with the track and guide assembly.
You are correct, you do have to remove the door panel to make the determination.

Oct 18, 2008 | 2003 Pontiac Grand Am

3 Answers

Driver side window

the window gears are worn out,

Aug 15, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
1995 Mercury Grand Marquis Logo

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

76682 Answers


Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides