Question about 2000 Chrysler Grand Voyager

1 Answer

My stop lights are not working depite that I chnaged the bulbs and checked the fuses

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    what about the switch??

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 244 Answers

Check brake light switch located near pivot point on brake pedal. Check for power at and through switch.

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota camry,rear brake lights not working,is there a fuse box under hood?


put a prybar between seat and brake pedal and use a test light on the wire in trunk where bulbs are sometimes bulbs look good but aren't or you got wrong bulb. a test light will verify that and make sure test light lights

Feb 16, 2015 | Toyota Cars & Trucks

1 Answer

Brake lights


chnage bulb or check fuse

Aug 22, 2013 | 2006 Toyota Fortuner 3,0

2 Answers

2 out of 3 brake lights dont work


If any light lights up when you apply brakes, then the brake switch is ok. The problem could be a fuse and/or a relay. or the bulbs. Those bulbs are dual filament so one filament could be bad, for stop or tail lights.

Oct 02, 2012 | 2002 GMC Envoy XL

2 Answers

Roof light stopped working


Fuses do not cause bulbs to burn out. You probably have a defective light fixture.

May 28, 2012 | Cars & Trucks

1 Answer

Stop lights do not work.


Pull bulb, have someone with volt meter check for voltage while you step on brake pedal. Make sure you have correct bulbs also.

Feb 04, 2010 | 1998 Chevrolet Malibu

1 Answer

Turning Lights Not Working


If you put a 2 element bulb in a single bulb elemet socket you would or could destroy the flasher unit. Especially if it is a electronic flasher try replaceing the flasher but get mechanicl flasher they last longer.

Jul 09, 2009 | 1998 Toyota Sienna

1 Answer

Left rear brake light stopped working but bulb and fuses are OK.


These are Dual Function Bulbs. They control the Parking Lights and the Brake Lights. This Bulb is Burnt out on the Brake Coil inside the Bulb. I have actually seen Bulbs that were Bad But you could not Tell by jast looking at them. It should be fine with a New Bulb. Please Rate My Response! Thanks!

Feb 05, 2009 | 1999 Ford Expedition

1 Answer

Need fuse schematic


if the fuse was blown the stop lights on both sides would be inop, also if the stop light circuit were dead u would be unable to get the trans out of park, use a 12 volt test light and test the brake light switch at the top of the brake pedal, u can buy a test light from Autozone, kragen and others for about $5 US. If the system has power cjheck the bulb socket it may be defective, use the 12 volt test light while someone pushes the brake pedal. let me know what u find and i will give u further assistance as ness.

Dec 31, 2008 | 1999 Dodge Durango

1 Answer

No dash lights and no tail lights


Check for faulty wires at the fuse block, had one fall off from the block itself from the rear, or it could be a wire break somewhere along the way.

Stop Lights and Blinkers are independant fuse.

Tail lights are on there own fuse and could be a wire break in the rear or removing the bulb and using a metre check for signal at bulb socket where trouble is, Check for disolored connections, Green in color or simular, could be a bad connection which in turn is not letting the curent to other side, Causing a short and loss of power to all remaining lights in curcuit.

Sep 15, 2008 | 1999 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Grand Voyager Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...