Question about 2006 Toyota Sienna

1 Answer

Hello, We have a 2006 Sienna. When the ignition

Hello, We have a 2006 Sienna. When the ignition key is turned off, within a few seconds, the cooling fan under the hood comes on full blast. This caused the battery to drain to the point of having to jump start the vehicle. I also noticed that the red light with a key was flashing, this is the lock out indicator I believe. When I shut the vehicle off while the car was in reverse, the fan did not go on, but the red light with key still flashes. However, in P, D, N the fan went on moments after I shut it off. Any ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,156 Answers

Its all electronic and fortune to fix ,cut the solonoid feed wire from the loom the thin one that makes the solonoid click on ,not the big heavy wire and fit another relay using this wire thats wired through the ignition switch so when the ignition is turned off it will isolate the original feed wire to the original solonoid

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming a honda transponder key


did some quick research for you and found this easy and very clear step by step instructions on how to program your transponder car key to your vehicle.. this works for the following models though :

Accord 2003 to 2006

Civic 1999 to 2006

Element 2003 to 2006

Odyssey 1999 to 2006

Prelude1999 to 2001

Accord SE 1997

CR-V 1998 to 2006

Insight 2000 to 2006

Pilot 2002 to 2006



now here are the steps:


  1. Turn the ignition on
  2. Press Lock/Unlock within 4 seconds
  3. Turn ignition off and hen back on within 8 seconds
  4. Repeat steps 2-3 two times
  5. Press Lock/Unlock again within 4 seconds. The system should now lock and unlock the vehicle to indicate it is in programming mode.
  6. In the next 10 seconds: press Lock/Unlock button allowing the doors to lock/unlock once; then press lock/unlock button of each remaining key, allowing the doors to lock/unlock once.
  7. Switch ignition off and then remove the key


Civic 1996-1998

  1. Turn ignition on
  2. Press and hold the valet button which is situated on the radio within 5 seconds.
  3. System should now lock and unlock the vehicle indicating it is in the programming mode
  4. Within 5 seconds turn ignition OFF and press Lock/unlock on the remote fob to be programmed
  5. Within the next 10 seconds, press Lock or Unlock of any remaining keys, allowing the doors o lock or unlock once.
  6. Release valet key
  7. Switch ignition off and then remove the key


Radio remotes 2 and 3 button types

  1. Switch ignition on and repeat for 3 times.
  2. Press he lock button, switch the ignition off and back on and then press lock button again.
  3. System should now lock or unlock
  4. Press the lock button of all remotes to be coded. The car should acknowledge this by locking/unlocking each time
  5. Switch ignition off to exit the programming mode.


If you will have any further doubts or question to ask i suggest you to check out the page where i found this which is http://www.carkeyadvice.com/step-by-step-fob-programming-guides/honda :) i hope this was the solution you were looking for mate! happy happy new year!

Dec 30, 2012 | 2007 Honda Pilot

1 Answer

Just replaced the battery with a new purchased-at-dealer Honda OEM battery. The car starts right and within 2-3 seconds it shuts off with the "key" light flashing for the theft deterrent system....


SYSTEM ARMS AFTER SWITCHING IGNITION OFF, SWITCH IGNITION ON, IMMOBOLIZER WARNING LAMP ILLUMINATES FOR A FEW SECONDS,IF IMMOBOLIZER WARNING LAMP ILLUMINATES FOR A FEW SECONDS THEN FLASHES RAPIDLY,KEY CODE NOT RECOGNIZED, REMOVE KEY AND TRY AGAIN,IF THIS PROCEDURE FAILS.THE DEALERSHIP WILL HAVE TO REPROGRAM KEYS AND THE IMMOBOLIZER.

Mar 21, 2011 | 2006 Honda Civic Hybrid

1 Answer

A red flashing car shape light flashing on my 06 toyota sienna van?


Is the immobilizer, if there is no key in the ignition is ok if flashes, if it flashes when the key is in the ignition the key is bad car wont start.

Dec 31, 2010 | 2006 Toyota Sienna

1 Answer

Ignition wont start the car when hot outside. U have to turn the key to the start position and hold for a few seconds or even crank or turn turn key the key past the start position to sometimes get it to...


My 2006 PT Cruiser has the same problem! When hot in the cab it won't start but after it is cool outside it starts up without missing a lick! When it is hot and you turn the key you get nothing but do have power to lights, radio, etc. weirdest thing ever and nobody knows why! We have had the ignition module replaced and have a new battery. This one has stumped everyone. Any suggestions folks?

Jul 24, 2010 | 2006 Chrysler PT Cruiser

1 Answer

How to reset maint req lite on a 2005 sienna


Reset the "MAINT REQD" Light on Toyota Sienna:
  1. With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B).
  2. Turn the car off (ignition key to the OFF position).
  3. Push in AND HOLD the button/knob that switches the odometer
  4. Turn key to ON position without starting the car. You will notice the maintenance light blink and go out.
  5. Release the odometer button/knob.
  6. Turn key to OFF position.
  7. That's it! The "MAINT REQD" light has been reset to warn you to change your oil in another 5,000 or 7,500 miles or so.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 2006 Toyota Sienna

1 Answer

Hi I want to program a new keyless fob. I have the original fob that works great.Do I need to do anything to the original key when I program the new fob? 2006 nissan altima


1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Nov 16, 2009 | 2006 Nissan Altima

2 Answers

Key fob not working after battery change ford focus 2006


Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

May 28, 2009 | 2006 Ford Focus

1 Answer

How do I program my key for my 2006 Chevy Impala?


Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

May 20, 2009 | 2006 Chevrolet Impala

2 Answers

2000 Toyota Sienna Minivan car alarm goes off.


1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Apr 25, 2009 | Chevrolet Malibu Cars & Trucks

1 Answer

Keyless entry remote


hello Kirk , follow these instructions carefully :

sitting in car with all the remotes you wish to register with the vehicle readily available ,,close all doors ! insert key into ignition and remove 6 times within 10 seconds ,, (hazzard warning lamps will then flash twice) ** note withdraw key completely from the cylinder each time ,, if procedure is done too fast it will not enter registration mode ,, ok ,, insert ignition key into cylinder and turn to the accessory position ,, Push any button on the key fob once ,, (hazzard warning lamps will then flash twice),, at this time the new ID code is entered ,, at this time open drivers door ,, check operation of all remotes ..

enjoy Mate .

Jan 04, 2009 | 2006 Nissan Altima

Not finding what you are looking for?
2006 Toyota Sienna Logo

493 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...