Question about 2006 Chevrolet Trailblazer

1 Answer

How do i remove alternator? 06 Chev Trailblazer

How do i remove alternator on a 2006 Chev Trailblazer? having problems getting to lower bolt...

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 22,156 Answers

If you cannot remove the bolt then remove whatever is blocking your access

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get to my thermostat in a 2006 chevy trailblazer I6


Must remove the alternator and alternator bracket to get to it. There are 2 bolts that are a bugger to get to. Bottom bolt on the alternator bracket, use a wracheting closed end wrench. Same with the bottom thermostat bolt.

May 05, 2011 | 2006 Chevrolet Trailblazer

2 Answers

Procedure to replace alternator 2006 mercury mariner 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the lower splash shield bolts and the pin-type retainers.
    NOTE The LH lower splash shield must be removed before the RH lower splash shield.
  3. Remove the lower splash shields.
  4. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside
  5. Disconnect the alternator electrical connector.
  6. Position the alternator B+ protective cover aside and remove the alternator B+ terminal nut.
  7. Remove the A/C compressor bolts. Use a tie-strap and position A/C compressor aside.
  8. Loosen the alternator nuts.
  9. Remove the lower alternator studs.
  10. Remove the upper alternator bolt and the alternator.

0996b43f80200f35.gif

Feb 18, 2011 | 2006 Mercury Mariner

1 Answer

How do you do it--alterenator replace 2006 dodge van


Hi there, you did not specify the type of engine you use so here are possible guides for varying enginge types:

2.4L Engine
To Remove:

1. Disconnect the negative battery cable.
2. Disconnect the intake air temperature sensor and remove the air cleaner assembly.
3. Remove the EVAP purge solenoid and move it out of the way.
4. Disconnect the wiring from the alternator.
5. Remove the accessory drive belt from the alternator.
6. Remove the alternator.

To Install:

1. Install the alternator.
2. Install the accessory drive belt
3. Connect the wiring to the alternator.
4. Install the EVAP purge solenoid in the bracket.
5. Install the air cleaner and duct, then connect the intake air temperature sensor.
6. Connect the negative battery cable.

3.3L & 3.8L Engines
To Remove:

1. Disconnect the negative battery cable.
2. Disconnect the wiring from the alternator.
3. Raise and safely support the vehicle.
4. Remove the right front tire and lower splash shield.
5. Remove accessory drive belt.
6. Remove the lower engine oil dipstick tube bolt, then remove the wiring harness from the dipstick tube.
7. Remove the 3 mounting bolts.
8. Lower the vehicle.
9. Remove engine oil dipstick tube.
10. Roll and carefully remove the alternator from vehicle.

To Install:

1. Place the alternator into position on the engine.
2. Install upper mounting bolts to hold the alternator in place.
3. Lubricate the o-ring with engine oil and install the dipstick tube.
4. Install the upper dipstick tube bolt.
5. Connect the wiring to the alternator.
6. Raise and safely support the vehicle.
7. Install the alternator lower mounting bolt and tighten.
8. Install the lower oil dip stick tube bolt.
9. Install the accessory drive belt.
10. Install the right front splash shield and tire.
11. Lower vehicle.
12. Install the wiring harness at the dipstick tube
13. Connect the negative battery cable.

Hope these help.

Jan 28, 2011 | 2006 Dodge Grand Caravan

1 Answer

How to remove altenator on 2006 dodge grand caravan


Removal & Installation 2.4L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Disconnect the intake air temperature sensor and remove the air cleaner assembly.
  3. Remove the EVAP purge solenoid and move it out of the way.
  4. Disconnect the wiring from the alternator.
  5. Remove the accessory drive belt from the alternator.
  6. Remove the alternator.
To Install:
  1. Install the alternator.
  2. Install the accessory drive belt
  3. Connect the wiring to the alternator.
  4. Install the EVAP purge solenoid in the bracket.
  5. Install the air cleaner and duct, then connect the intake air temperature sensor.
  6. Connect the negative battery cable.
3.3L & 3.8L Engines To Remove:
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring from the alternator.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and lower splash shield.
  5. Remove accessory drive belt.
  6. Remove the lower engine oil dipstick tube bolt, then remove the wiring harness from the dipstick tube.
  7. Remove the 3 mounting bolts.
  8. Lower the vehicle.
  9. Remove engine oil dipstick tube.
  10. Roll and carefully remove the alternator from vehicle.
To Install:
  1. Place the alternator into position on the engine.
  2. Install upper mounting bolts to hold the alternator in place.
  3. Lubricate the o-ring with engine oil and install the dipstick tube.
  4. Install the upper dipstick tube bolt.
  5. Connect the wiring to the alternator.
  6. Raise and safely support the vehicle.
  7. Install the alternator lower mounting bolt and tighten.
  8. Install the lower oil dip stick tube bolt.
  9. Install the accessory drive belt.
  10. Install the right front splash shield and tire.
  11. Lower vehicle.
  12. Install the wiring harness at the dipstick tube
  13. Connect the negative battery cable.
prev.gif next.gif

Jan 16, 2011 | 2006 Dodge Grand Caravan

1 Answer

Trying to remove an alternator from an 06 altima


Removal and Installation L4-2.5L (QR25DE) Engines To Remove:
nis_alt_l4_alt.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Engine cover
    • Front/right-side engine undercover
    • Drive belt
    • Alternator harness connector
    • Engine ground wire from top mount
    • Alternator upper and lower mounting bolts
  3. Set the alternator aside and remove the top mount.
  4. Remove the alternator.
To Install:
nis_alt_l4_alt1.gif

  1. Slide alternator in place.
  2. Install or connect the following:
    • Alternator top mount
    • Alternator upper and lower mounting bolts
    • Engine ground wire from top mount
    • Alternator harness connector
    • Drive belt
    • Front/right-side engine undercover
    • Engine cover
    • Negative battery cable
V6-3.5L (VQ35) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain coolant from the radiator into a suitable container.
  4. Remove or disconnect the following:
    • Radiator
    • Front/right-side engine under cover
    • Drive belt
    • Idler pulley
    • Alternator adjustable top mount
    • Alternator lower mount bolt and nuts
    • Alternator lower front bracket bolt
    • Alternator harness connectors
    • Alternator
To Install:
nis_alt_chg_v6.gif

  1. Install or connect the following:
    • Alternator in place
    • Alternator harness connectors
    • Alternator lower front bracket bolt
    • Alternator lower mount bolt and nuts
    • Alternator adjustable top mount
    • Idler pulley
    • Drive belt
    • Front/right-side engine under cover
    • Radiator
  2. Replace the engine coolant.
  3. Connect the negative battery cable.
  4. Start the engine and check for leaks.
  5. Recheck coolant level and top off as needed.
prev.gif next.gif

Oct 15, 2010 | 2006 Nissan Altima

1 Answer

The battery and the alternator, need replacing on a 2006 6cyclinder, Taurus. I have the parts, and tools, I just never worked on a newer car before. I need a print out of instructions, please!!


Removal & Installation 3.0L (2V) To Remove:
  1. Disconnect the battery ground cable
  2. Remove the accessory drive belt
  3. Remove the fasteners and move the degas bottle aside.
  4. Disconnect the wiring from the alternator.
  5. Remove the brace and the alternator mounting bolt.
  6. Remove the alternator from the engine.
To Install:
  1. Install the alternator on the engine. Tighten the lower and right brace bolt to 18 lb-ft. (25 Nm) and the left brace bolt to 35 lb-ft. (48 Nm).
  2. Connect the wiring to the alternator.
  3. Install the degas bottle in the original position.
  4. Install the drive belt.
  5. Connect the negative battery cable.
3.0L (4V) To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt.
  3. Remove the power steering hose bracket nut from the alternator mounting bolt.
  4. Remove the upper alternator mounting bolts. NOTE: The left side bolt will come out with the alternator.
  5. Raise and safely support the vehicle.
  6. Remove the right front wheel.
  7. Remove the right inner fender splash shield.
  8. Remove the screws and the alternator splash shield
  9. Remove the torque converter inspection cover.
  10. Install the flywheel holding tool. holdingtool.gif
  11. Remove the bolt and the crankshaft pulley. NOTE: The crankshaft pulley bolt has a reverse thread. The crankshaft pulley and bolt are a molded composite and are one piece.
  12. Lower the alternator to allow access to the electrical connectors.
  13. Disconnect the crankshaft sensor.
  14. Release the oxygen sensor connector locator from the bracket.
  15. Remove the lower alternator bolt.
  16. Disconnect the regulator electrical connector.
  17. Disconnect the remaining wiring from the alternator and remove the alternator
To Install:
  1. Position the alternator on the engine while making the necessary electrical connections.
  2. Connect the voltage regulator electrical connector.
  3. Install oxygen sensor connector locator in bracket.
  4. Connect crankshaft sensor.
  5. Raise alternator and install upper alternator bolts (left side bolt is installed with alternator). Torque upper and lower bolts to 18 lb-ft. (25Nm).
  6. Position the wiring harness locator and install nut.
  7. Install the alternator splash shield and the screws.
  8. Position crankshaft pulley and install bolt (reverse thread). Torque to 74 lb-ft. (100Nm)
  9. Remove the flywheel holding tool.
  10. Install the inner fender splash shield.
  11. Install the right front wheel.
  12. Install the torque converter inspection cover.
  13. Lower the vehicle.
  14. Install the power steering hose bracket nut from the alternator mounting bolt.
  15. Install accessory drive belt.
  16. Connect the battery ground cable.
prev.gif next.gif

Jul 18, 2010 | 2006 Ford Taurus

1 Answer

Where is the alternator located on a 2006 Ford Taurus?


Hi,

If yours is the 3.0L (2 valve) engine, then location will be obvious - next to the degas bottle on the engine.

However....if it's the 3.0L (4 valve) engine, then:
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt.
  3. Remove the power steering hose bracket nut from the alternator mounting bolt.
  4. Remove the upper alternator mounting bolts. NOTE: The left side bolt will come out with the alternator.
  5. Raise and safely support the vehicle.
  6. Remove the right front wheel.
  7. Remove the right inner fender splash shield.
  8. Remove the screws and the alternator splash shield
  9. Remove the torque converter inspection cover.
  10. Install the flywheel holding tool.
  11. Remove the bolt and the crankshaft pulley. NOTE: The crankshaft pulley bolt has a reverse thread. The crankshaft pulley and bolt are a molded composite and are one piece.
  12. Lower the alternator to allow access to the electrical connectors.
  13. Disconnect the crankshaft sensor.
  14. Release the oxygen sensor connector locator from the bracket.
  15. Remove the lower alternator bolt.
  16. Disconnect the regulator electrical connector.
  17. Disconnect the remaining wiring from the alternator and remove the alternator
I know....what a pain !


Cheers,

Scott

Nov 12, 2009 | 2006 Ford Taurus

1 Answer

I have a chev 06 trailblazer, trying to change light on drivers side... i do not see two rods to pull out, i do see that the lights look like its covered with black circular rubber


All standard headlight bulbs are halogen, if you get the numbers off the bulb you should be able to cross reference it at a parts store. If you have no idea what it is you can call a dealership and they will tell you exactly what you need, they will need the vin #.

Oct 30, 2009 | 2006 Chevrolet Trailblazer

2 Answers

4.2L 2006 Trailblazer


you will have disconect the neg.-BAT TERMINAL then loosen alt. adjusting bolt,remove alt. belt( or remove serpentine belt if so exist) then remove the two existing bolt at the bottom of the alt.then remove altenator.ree-install in reverse direction.

Jul 19, 2008 | 2006 Chevrolet Trailblazer

1 Answer

Chev trailblazer strut removal


Hi, removal of the struts need some mechanical knoledge and must be carefull removing the spings,secure your car with a jack stand remove the tire ,position a jack onder lower control arm,disconect brake line ,remove the three screws on top of the strut ,remove the two nuts and screws at the lower end of the strut ,lower the jack slowly ,the strut assembly should come out, you need a strut sprig compressor to compress.the springs,remove the nut at the center of the strut,rplace the stut,instalation is the reverse of the procedure..Good Luck

Jul 09, 2008 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2006 Chevrolet Trailblazer Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...