Question about 2003 Toyota Camry

1 Answer

What are the torque specs for the bolts on the brake rotors/calipers?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 862 Answers

FRONT CALIPAR TO CARRIER 34NM
FRONT CARRIER TO HUB 107NM
FRONT HUB NUT 294NM
REAR CARIER TO HUB 62NM
REAR CALIPAR TO CARRIER UPPER BOLT 39NM
LOWER BOLT 34NM

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Kia Optima Brake Torque Spec


Bracket bolts Front 16-24 ft/lbs
Caliper bolts Front 51-63 ft/lbs Rear 16-24 ft/lbs

Feb 03, 2017 | 2004 Kia Optima

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

1 Answer

Volvo torque specs


Along with many of the others the bolts holding the brake caliper slides in place are stretch bolts. You torque them up as pe the first post and then its a twist of so many degrees. This stretches the bolt past its elastic limit. Once used just like an engine head bolt the bolt is scrap. I'm told its to keep the wieght down on the front. My personal feel is that its a dangeous practice because you know loads of Volvos will have had the bolts used for a second and third time.

Jul 19, 2014 | 2005 Volvo S80 2.5

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

2 Answers

What would make the car pulsate when breaking while the brakes and rotors appear good.


Normally this is caused by uneven rotors or drums, replacing brakes and not resurfacing drums

or rotors, or replacing drums or rotors, old brake fluid in system, not flushing out lines, dirty

brake fluid causing brake calipers to hang-up. inproperly installed brakes, not torqueing down

the bolts, loose bolts. good luck!

Jun 25, 2011 | 1999 Oldsmobile Aurora

1 Answer

Need torque specs for brake caliper bracket bolts.2000 grand prix


Hello and welcome. here is the torque specs for the bolts.

Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
Caliper Bolts
85 N·m
63 lb ft
Caliper Bracket Bolts
180 N·m
133 lb ft
caliper brake bracket bolts torque to 180 n.m or 133 ft.lbs

Jul 26, 2010 | 2000 Pontiac Grand Prix

2 Answers

Brake job torque spec


Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

Nov 13, 2009 | 2005 Honda Civic

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2003 Toyota Camry Logo

548 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...