Question about 2002 Jaguar X-Type

1 Answer

How to install rear break pads?

Cant compress rear calipers do i need a special tool?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 22,219 Answers

Put a G clamp on the piston and dont tighten it too much then turn the piston clockwise with some water pump pliers and then tighten the clap a bit more then turn piston again ,also watch it because some of these use left handed threads if its the ford made caliper

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I get the rear brake pad assembly back on the rotar? The new pads make the space between them too narrow for the assembly to fit over the rotar


You have to compress the caliper. If your design uses the brake pads as parking break, you need to rotate the piston while compressing it. there are tools that assist with this, but I use a C clamp and the old brake pad.

Jan 01, 2011 | 2004 Honda Accord

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

2 Answers

Change rear break pads on 2000 Buick. Cannot compress break cylinder in order to install new pads using C clamp and bleeding off break fluid.


There's a special tool required to compress the rear caliper pistons. You may want to rent the tool. If you look at the piston you'll see one or two notches. The special tool has nipples to fit these notches. The caliper piston will have to be compressed with the tool and the notches will have to be placed in the o'clock and 6 o'clock for the brake pads to slide over the rotor. If you rent the special tool have the renter show you how to use it.

Sep 11, 2010 | 2000 Buick LeSabre

3 Answers

How do i compress the the calipor piston on the rear breaks, is there a special too?


yes, you can rent one from Auto Zone, Advanced Auto Parts, etc.

Jun 12, 2010 | 2003 Jaguar X-Type

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

2 Answers

Have no special tool how do i compress the rear caliper on S40


u need to open the pads wide enough to put it back
if you cant do it by hand go buy a pad expanding tool they are cheap

Jul 17, 2009 | 2001 Volvo S40

3 Answers

Are any special tools required or any special process to change the rear brake pads on a 2006 Jetta? I have changed pads on BMW's Fords Chevys etc....but you never know, so I thought I'd ask. thanks!


These cars usually have disk brakes in the back. You need a caliper piston rotator tool, this tool fits into the caliper piston and you must turn it in to retract the piston, it fits onto a 3/8 " drive socket wrench. Npa sell a universal one for like $15.00 - $20.00.

Jul 08, 2009 | 2006 Volkswagen Jetta

1 Answer

I am replacing the rear pads and cannot get the caliper to compress using a c-clamp. Is there something special I need to do or know on my montego 05 car to get the caliper to compress? Sincerely Desperate...


One, take your brake fluid reservoir cap off.
Two, use a thin piece of wood to help you compress the piston on the caliper....do it slow. This way, you don't create a lot of pressure to the reservoir and it won't overflow.
Three, these are the steps to removing and replacing the pads for the rear. It does mention a special tool....but you can use a c-clamp for the same purpose:

Rear To Remove:
  1. Check the brake fluid level in the brake master cylinder reservoir.
  2. If required, remove the fluid until the brake master cylinder reservoir is half full. CAUTION
    Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever.
  3. Remove the disc brake caliper. Support the caliper with mechanic's wire. CAUTION
    When the brake pads are separated from the brake caliper, new brake pads must be installed. The brake pads are one-time use only.
  4. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed.
  5. Inspect the brake caliper anchor plate assembly.
  6. Check the guide pins and boots for binding or damage.
  7. Install a new brake caliper anchor plate if it is worn or damaged.
To Install:
NOTE: The left caliper piston turns clockwise and the right caliper piston turns counterclockwise.
  1. Using the special tool, turn and compress the brake caliper piston into the cylinder.
  2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. CAUTION
    Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface. Do not install contaminated pads.
    NOTE: Install all the new hardware supplied with brake pad kit.
  3. Install the new spring clips and brake pads.
  4. Position the brake caliper and install the 2 bolts. Tighten caliper bolts to 23 ft-lbs (31 Nm).
  5. If necessary, fill the brake master cylinder reservoir with clean brake fluid.
  6. With the engine running, apply pressure on the brake pedal to seat the brake pads.
  7. Test the brakes for normal operation.

May 17, 2009 | 2005 Mercury Montego

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

1 Answer

Changing rear breaks


Try tapping around the rotor hat (the area that actually fits over the hub, where the lug bolt holes are) with a hammer. That usually will loosen up a rotor that's stuck due to heat, dust, etc. As for compressing the rear piston, they're a screw-in design, not a compression design like the front calipers. You need a piston retracting set (you can borrow them from AutoZone), and with that you can screw the pistons into the calipers. After removing the reservoir cap underhood, screw them all the way in so that you have ample clearance for the new pads over the new rotors, then pump the brakes a few times before you hit the road (put the reservoir cap back on first).

Oct 12, 2008 | 2001 Audi A8

Not finding what you are looking for?
2002 Jaguar X-Type Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...