Question about 2002 Suzuki Aerio

1 Answer

How to asamble the back brakes - 2002 Suzuki Aerio

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 22,156 Answers

Take one side off at a time so you know you can look at the other side too see how the springs go back on

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bolero pick truck front brake skid but back wheel brake roll on..load and unload.difficult to adjust, why plz help...!


Might be a leak somewhere in brake lines. Or some gasket gone bad in brakes (then there is probably a leak as well). If no leak then I assume there is some air in the brake system, sounds like in lines which lead to back brakes so I suggest you bleed back brakes (preferably bleed the whole brake system). In my car (not bolero though) there is some kind of braking power balancing system with extra bleeding screw at the back and this could have air in too. You can find further information how to bleed braking system from your car manual or generally from the Internet. Usual drill is to bleed the furthest brake first then continue until closest brake to your car brake fluid reservoir.
PS: If your brake pedal feels soft and get harder by each push then there is definitely air in the system. If it stays soft you might have a leak.

Oct 29, 2013 | Cars & Trucks

2 Answers

How do i get the brake piston back so i can fit the new brake pads , to enable me to get them back over the brake disc ?


remove some brake fluid from mastercylinder, then use large c - clamp with the old brake shoe in place tighten c - clamp to push piston back in the bore.put cover back on mastercylinder. be sure to pump brake pedal to seat new brake shoes to the brake rotor.and check brake fluid level in mastercylinder.dont drive car until you get firm solid brakes.

Sep 21, 2011 | Mitsubishi Colt Cars & Trucks

2 Answers

Center brake light working but neither tail light brakes working both bulbs good


the center and brake light are not on the same circuit, check voltage coming from the switch

Mar 28, 2011 | 2001 Dodge Durango

1 Answer

Diagram for parking brake cables


Removal & Installation
  1. For the 1500HD, relieve the tension from the park brake cable by pulling down on the park brake cable in front of the equalizer then removing the cable from the equalizer bar.
  2. For the 25/35 series Disable the park brake cable automatic adjuster.
  3. Raise and safely support the vehicle.
  4. Remove the tire and the wheel.
  5. Perform the following procedure to remove the cable (2) from the backing plate (4):
    • Compress the spring (3) by pushing toward the lever (1).
    • Depress the locking tabs.
    • Pull the cable housing out of the backing plate (4).
    • Remove the cable (2) through the slot in the backing plate.
      32085_silv_g0069.gif

      Lever (1), cable (2), spring (3) and backing plate (4)

  6. Remove the park brake cable (2) from the lever (1).
  7. Remove the rotor.
  8. Remove the rear axle shaft.
  9. Remove the park brake shoe return spring (6).
    32085_silv_g0070.gif

    Park brake shoe assembly 1500HD, 25 and 35 Series
    Click to Enlarge

  10. Remove the park brake shoe anchor springs and pins.
  11. Separate the tips of the shoes from the park brake actuator and remove the park brake shoes and adjuster assembly from the vehicle.

To install:

  1. Clean the debris and the dust from the park brake components using a clean shop cloth.
  2. Install the adjuster assembly to the park brake shoes.
  3. Separate the tips of the shoes and install the park brake shoes to the park brake actuator.
  4. Install the park brake shoe anchor springs and pins.
  5. Install the park brake shoe return spring (6).
  6. Adjust the park brake shoe.
  7. Install the rear axle shaft.
  8. Install the rotor.
  9. Install the park brake cable (2) to the lever (1).
  10. Perform the following procedure to install the cable (2) to the backing plate (4):
    • Compress the spring (3) by pushing towards the lever (1).
    • Route the cable (2) through the slot in the backing plate.
    • Push the cable housing into the backing plate (4) until the locking tabs snap into place.
  11. Install the tire and wheel.
  12. Remove the safety stands.
  13. Lower the vehicle.
  14. Enable the park brake cable automatic adjuster.
  15. For the 1500HD, install the park brake cable to the equalizer by pulling down on the park brake cable in front of the equalizer then installing the cable to the equalizer bar.
  16. Adjust the park brake cable.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 23; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; shinehutt_0.gif

Jan 13, 2011 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Back right brake caliper leaking brake fluid


Sounds like the brake line is just rusted, you'll probably have to change the brake line and then bleed the brakes

Oct 15, 2009 | 1995 Nissan Maxima

1 Answer

How to change back brakes 1999 ford windstar, back brakes are grinding, brake light on


does it have rear disc brakes or drum brakes, if disc brakes should be changed just like the front and you might have an emergency brake shoe inside the rotor that they call a halo shoe, if it is drum brakes take off the adjusting spring and the return spring remove the brake adjuster,the the brake bar then remove the brake shoe hold down spring by holding the pin from the back and pushing and turning the spring to remove from the pin, you might have to remove the the emergency brake bar from one shoe by removing the horseshoe clip from the pin on the shoe if you have problems putting it back together look at the other side that you have not torn down yet.

Aug 12, 2009 | 1999 Ford Windstar

1 Answer

2005 MAZDA 6 BRAKE PADS


Since you are taking it back, have them check all the brake lines in front, and the wheel cylinder (if the back has drum breaks). Although you had only the front done, it's a good ideas to have them check the back brakes, and the master cylinder. Check your brake fluid before taking it back and make sure it's full, if so, you may just have air in the brake lines. If this is the case, either they forgot to bleed the brakes, or didn't bleed them enough.

Apr 01, 2009 | 2005 Mazda 6

1 Answer

Back drum brakes


Remove the rubber plug at the back of the backing plate. Take a brake adjusting tool or screw driver through the hole and turn(pry) the brake adjuster to back off the brake shoes. There is a ridge worn in to the brake drum and that is keeping the brake drum on, even if you can wiggle it.

Mar 23, 2009 | 1988 Dodge D-Series Pickups

1 Answer

Passenger power window doesn't work at all.


bad window regulator and motor by complit asambly and replece

Mar 13, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Suzuki Aerio Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...