Question about 2001 Ford Escape

1 Answer

#4 cylander is misfiriing where is the # 4 cylander located on a 2002 Ford escape 6cyl. 4x4

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

Middle cylinder on firewall side of engine. Front is 1-3-5, firewall side is 2-4-6 from front of engine.

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am having difficulty locating it. I need to know how to locate and replace a thermostat on a 2002 ford escape


Follow the top radiator hose down to where it connects to the engine. You should find a dome shape item or a couple of smaller bolts that attach to the engine to the side of the radiator hose and the thermostat will be inside the housing. You will need to drain the radiator, remove the bolts holding the thermostat housing to the engine and remove the old stat and put in a new one be sure to make note of how the stat is facing when you remove it and put the new one in the same way. then reconnect the thermostat housing making sure the gasket is in place so it won't leak, then refill the radiator slowly so you don't cause an air lock in the radiator, with cap still off start the engine and allow it to warm up until the stat opens and then you will need to add more antifreeze to the system. Double check for any leaks. Turn on the heater and make sure you have good heat and you should be good

Jan 11, 2016 | Ford Cars & Trucks

1 Answer

I was wondering if the transmission from a 2003 ford ecsape 3.0 with 4x4 would fit in a 2001 ford escape 3.0 with 4x4


just put an engine out of a 2004 in my 2002 escape 4X4 3.0L you should be perfectly fine.

Sep 27, 2013 | Cars & Trucks

1 Answer

Car stalls on a cold start what could be the problem?


Check fuel pressure. If ok; replace the Idle Control Valve. Auto Zone has it for $46.

Nov 26, 2012 | 2002 Ford Escape

1 Answer

Serpentine belt diagram 2002 ford escape with air


Assuming you have the 6cyl 3.0L engine, your diagram is below. Please post back if you have a different motor.

2002 3.0L Ford Escape

greg_margo_10.jpg

Apr 22, 2011 | 2002 Ford Escape

1 Answer

WHERE IS THE OIL PRESSURE SENSOR on a 2002 ford escape


On 4 cylinder engines: The oil pressure sending unit is located in the rear of the block near the oil filter housing
On 6 cylinder engines: Sending unit is located near the oil filter housing behind the air conditioning compressor, on the front side of the block

Dec 22, 2010 | 2002 Ford Escape

1 Answer

Cylinder layout for 2002 ford escape


Cylinder layouts for the 4cyl and 6cyl:


zeevert_17.jpg


zeevert_18.jpg

Nov 30, 2010 | 2002 Ford Escape

1 Answer

How do you remove and replace the alternator on a 2005 ford escape 4 cylander


Loosen the belt by loosing a tensioner bolt on the alternator. Disconnect the battery and cables from the alternator. Replace with new alternator and hook up the power cables to it. Then reconnect the battery and you're done. Mike. Rate 100% please.

Sep 18, 2009 | 2005 Ford Escape

1 Answer

Where is the iac on a 2002 ford escape 4 cylinder


I IAC is along the intake tube from the air filter housing to the Throttle body. There's going to be a two wire harness. It may even be on the air filter housing on the throttle body side. Good luck and hope this helps.

Jun 15, 2009 | 2003 Ford Escape

1 Answer

Rear exaust manafold won't move and line up with cylander head.


Are there studs or bolts on the front cylinder head? If there are bolts then secure the rear manifold first.Or replace the rear studs with bolts.

May 16, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
2001 Ford Escape Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...