Question about 2000 GMC New Sierra 1500

1 Answer

1977 gmc pu power window power supply not getting to the window swich where does the power start from to get to the window swich

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • GMC Master
  • 2,030 Answers

Right at the power window or acc. circuit in the fuse panel

Posted on Apr 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My 2004 gmc yukon denali has no power to driverside door no seat heater or window or lock switch is not working. The left arrow on mirror is working.

Try checking your fuses first, if all good then check power from the fuse panel to all the accessories you say are not working. Might want to also check the area under the carpet along driver side. Sometimes, the main harness gets wet and corrodes terminals that supply power to seat. May want to also check the wiring harness that runs to the door which is inside the rubber molding by the driver door hinges. Wires often break in this area.

Dec 18, 2016 | GMC Cars & Trucks

1 Answer

How to replace window motor 1995 gmc pu - 1995 GMC Sierra C1500

How To Install Replace Window Regulator Chevy GMC Pickup Truck SUV 88 98...
1995 GMC C1500 PICKUP 4 3L V6 Window Motor RockAuto

I have done one on a 1994 Astro, but this video shows a different set of circumstances. I have also linked a reliable parts source that I have used for years.

Apr 09, 2016 | GMC Cars & Trucks

2 Answers

2003 GMC SIERRA PU. 5.3 keep getting the " Reduced engine power " code , any Ideas on where I should' start looking?

You should take it to a garage that has a GMC scan tool and scan it for the error code.

Jul 31, 2015 | GMC Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle

QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)

see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer


Your battery is probably bad. Just because you have enough power to use the lights / accessories doesn't mean you have enough power to start the engine.

Feb 08, 2013 | 1972 Porsche 911

1 Answer

Need a pic. of the brake lite swich 1993 gmc pu

Should look like what's in the pictures below. I hope this helps and good luck.


Jul 29, 2011 | 1993 GMC Sierra

1 Answer

1977 gmc pickup window regulator removal?

You must remove the door panel. Then remove the glass from the frame which is held in place at the top of the regiulator by two nuts. Lower the regulator until the nuts become available to work on. After removing the nuts lower the regulator all the way and lift the window glass out sideways to the outside of the door frame top. If you rgulator is riveted in, then you'll have to drill out the rivets. I believe that there are 5 of them. You'll need a special rivet tool to replace them. The regulator will now fit out through the largest hole in the door panel structure. It is a bit or a chinese puzzle but it will come out eventually. If your regulator is electrical, make sure to remove the wire harness first. Thank you, Dana

Sep 26, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Wife turned off GMC Sierra & removed key when not in park gear

hold foot on brake pedal try turning key to on position to put truck all the way in park.

May 31, 2009 | 2001 GMC Sierra 1500HD

1 Answer

Starting problem

check your reverse swich. if the switch doesnt see connection, being out of reverse/in reverse, then the ignition switch will not get supply power. look for swiches/sensors by the shifter and ignition swich for possible faulty switch/sensor. hope this helps

Aug 09, 2008 | 1995 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides