Question about 1997 GMC Jimmy

1 Answer

How do you remove the wire connection for the turn signal/ wiper control arm1997 gmc jimmy

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

If you check/follow the wire loom from the switch/stalk it will route underneath lower dash alongside steer column then normally it has a plug which plugs into main loom when you req this switch/stalk as new it comes complete with its short wire loom fitted ready to fit/plug in

Posted on Apr 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 1993 gmc jimmy and I can't find the windshield wipers on and off switch

The wipers are controlled by the multi functions turn signal switch.
A thumbs up would be greatly appreciated if this answer is helpful to you.

Dec 19, 2014 | 1993 GMC Jimmy

1 Answer

1994 GMC 2500 pickup with wiper/turn signal/headlight problem.

sounds like you have rats in your dash,or someone has been doing some rewiring,there has to be wires shorted together wired together

Jan 10, 2013 | 1994 GMC Jimmy

1 Answer

1997 jimmy turn signals and windshield wipers quit working

Okay, we will need to pin point the short,first remove connector from wiper motor and install a fuse and see if it blows. if it does then we know its not the wiper, will fuse blow when key is turned on or do you have to turn on signals? if its when signals are working then check all bulbs, remove signal bulbs one at a time and make sure the correct bulb is in the socket and the bulb and socket are good, if all checks out then i would say you may have a bad switch,let me know what the outcome of these tests are i will help you fix problem or give you price. good day

Feb 22, 2012 | 1997 GMC Jimmy

2 Answers

When I turn on my signal light the wipers turn on

to correct this you must replace the mulitfunction switch.

Sep 18, 2009 | 1992 GMC Jimmy

1 Answer

Windshield wipers work intermittentaly

You may have a loose connection or more than likely a worn switch. This is probably a unitzed switch for the wipers and turn signals

Sep 13, 2009 | 1997 GMC Jimmy

3 Answers

1998 g.m.c. jimmy-turn signal flasher

I had same problem. You need to change the combo signal switch. I did find a sneeky way to do it without taking off steering wheel & air bag. There are two torx screws holing it on. The one in the front of switch is easy to get to. The other one toward the left under steering wheel is the pain. Get the proper torx bit, the bit should be about 1 in long. Put just the bit in the screw and use a quarter inch wrench to loosen it. This should save you about 1 hr & alot of work. Dont forget to remove battery cables first when working around the air bag (yellow wire)

Apr 16, 2009 | 1998 GMC Jimmy

1 Answer

2000 GMC Jimmy, Flasher clicks alot even after repalcing flasher

Auto headlights do go off when turn signal is put on. The wiper problem could very well be in the blinker switch in the column, they are know to go out on these trucks. Run some tests before replacing.

Feb 24, 2009 | 2000 GMC Jimmy

1 Answer

Wiper arm removal 1997 GMC Jimmy

youll have to raise the hood on the truck to access the screws that hold it in place there should be 2 of them holding it

Oct 25, 2008 | 1997 GMC Jimmy

1 Answer

1997 GMC Jimmy turn signal switch

I have a 97 Sierra and similar issues. I changed the wiper control board that is under the hood/on the firewall/ mounted on the wiper motor.

Oct 04, 2008 | 1997 GMC Jimmy

1 Answer

Turn Signals and High Beams are not working and I have checked the fuse what else could it be? Everything else is working

Sounds like the combination switch is bad. The comination switch is for the turn signals and high beams and sometimes cruise control and windshield wipers. The combination switch is the turn signal lever. Also might want to check turn signal flasher operation.

Sep 12, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides