- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The car is in theft mode and if you cant reset it with the remote key, you will need a shop to reset it for you. to try the reset with the remote, just use the lock button by pressing it twice, wait 3 minutes and use the unlock button by pressing twice, this should reset the alarm
reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.
turn key twice when opening, ie turn right. once drivers door will unlock, turn twice passengers doors will unlock, and locking is turn anti clock wise once will lock all doors, turn twice will set door dead locks.dead locks will stop openand lock internal button working and handle from opening door. the same actions can be applied to the remote one press drivers door, two press passenger doors, press and hold unlock button for 5 seconds and rear window will open.
TRY THIS PRESS REMOTE TRANSMITTER LOCK BUTTON ACTIVATES ALARMS AND LOCKS ALL DOORS.NOW PRESS REMOTE TRANSMITTER UNLOCK BUTTON DEACTIVATES ALARM AND UNLOCKS ALL DOORS AND TRUNK LID.IF VECHICLE UNLOCKED AND DOORS OR TAIL GATE NOT OPEN WITH IN 30 SECONDS LOCKS AND ALARM ARE REACTIVATED.IF YOU STILL HAVE TROUBLE WITH DOOR LOCKS THE DEALERSHIP HAS TO FIX.
It sounds like they disconnected your battery when they worked on your car.... Try this and see if it works..
1-insert and remove key from ignition two times
2-close and open driver door two times
3-insert and remove key once from ign.
4-close and open drvr door twice
5-insert key into ign.,then close driver door
6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.
7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.
8-press lock/unlock together and hold for a second
9-release,and press lock on remote,the door locks will cycle
confirming program.continue to do other remotes you have,steps 8 and
9.if only one in possession,you are done. To end mode open door or insert key into ignition.
You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works
If you are close to the truck when it happens, try removing the battery from the remote. Some times when remotes are worn, they can send out a constant signal setting off the alarm, unlocking the doors and so on. I would try that first. If it stops, then you verified the remote is the problem
This usually works.Lock the doors with the remote.Press lock twice sounding the alarm.Then press the unlock button twice.Your car should start now.If that doesnt work try this,Lock the car again with the remote once.Go over to the passenger side door and use the key to unlock the door then press in the door unlock all doors.Hopefully by now it worked.Now if none of these work your security probably malfunctioned and theres only two things that will work,One is disconnecting the battery for 5 mins then reconnecting.unlock doors.the start.If that doesnt work you'll have to take it to the dealer to get the security reset or replaced.The steps I have wrot you are the diagnostics to reset it.I hope these work for you and good luck.See ya had have a great day..
System warning lamp located on top of the instrument panel Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted) Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted) To activate alarm system (if fitted): Switch ignition OFF Open driver's door Press Lock button on remote Close Driver door warning lamp will flash when system is activated Press remote power sliding door button will open sliding door (if fitted) only if unlocked first Pressing remote panic button: *Sounds horn intermittently *Flashes exterior lamps *Turns on interior lamps **Pressing panic for the second time OR switching ignition ON deactivates alarm.
Remobe key from ignition switch Remove the "BCM PRGRM" fuse, from the fuse box Close all doors Turn ignition switch to the ACC position With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC' (really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds) Repeat this exact procedure for all remotes to be programmed Remove key from ignition Refit 'BCM PRGRM' fuse.