Question about 1992 Nissan Sentra 4 Door

Open Question

I want to change the shock absorbers on My 1992 nissan Pulsar Q Hatch and need instructions (with diagrams)

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: audio wiring diagram of a nissan datsun pulsar (N12) 1983

Constant 12V+ Red/Black Switched 12V+ Blue Ground n/a Illumination Red/Yellow Dimmer n/a Antenna Driver's Pillar Front Speakers 4" Dash Left Front (+) Blue/White Left Front (-) Blue/Yellow Right Front (+) Brown Right Front (-) Brown/White Rear Speakers 5 1/4" Side Panels Left Rear (+) Red Left Rear (-) Green Right Rear (+) Blue Right Rear (-) Pink

Posted on May 15, 2008

Ad
  • 33 Answers

SOURCE: I need the radio unlock

you need to get the serial number off the radio and call the dealership they should get you the code

Posted on Sep 27, 2008

  • 259 Answers

SOURCE: 1992 Nissan Pulsar XIR Electric windows not functioning,

check the fuse box for any blown fuses

Posted on Mar 30, 2009

jlisagearhea
  • 412 Answers

SOURCE: Car maintainance for Nissan Pulsar Vector 1990

Yes, Yes, Yes, and Yes.....All that you want to do you can perform yourself and save quite a bit of money.You can actually find a VERY VERY descriptive online manual(which i have too) at alldata.com You pay a $20 fee and you get online manuals for five years for one vehicle.Definitely worth it.This makes auto work much easier.Any other questions get back to me...I'M HERE TO HELP!!!

Posted on Dec 04, 2009

  • 15 Answers

SOURCE: i don't know what engine oil to top up my nissan

if you're in a bind anything's better than nothing. it's best to stick with a certain brand though. Decide on a 10w-30 or 15w30, and stick with it. If not sure what has been in the engine before, change the oil and filter. If switching to a synthetic, definitely change the oil and then top off with the synthetic.

Posted on Jan 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 1992 nissan pulsar radiator fit in a 1995 nissan pulsar


look it up on ebay. after searching for the right make and model, click on "see compatible vehicles"

Dec 15, 2014 | Nissan Cars & Trucks

1 Answer

How to change rear shock absorbers for 2006 ford focus


I am sorry we have no diagram's of this type. You can access allthe cars repair info for a fee at his site: alldatadiy.com

Feb 16, 2012 | Cars & Trucks

2 Answers

The trunk will not stay open on my 2007 Honda Odyssey? Any idea how to fix this?


there are springs or Shock absorbers attached to the hatch change the shocks or if its attached to a spring either its broken or its loose from either side

Jan 20, 2011 | 2005 Honda Odyssey

1 Answer

Dear Sir, How do you change an 87 mitsubishi mighty max front shocks without any compression equipment? Please email me at brad8141@hotmail.com. Is there a book with instructions regarding this...


REMOVAL & INSTALLATION
  1. Support the vehicle safely on jackstands. Support it at a height which will allow sufficient room to reach the upper shock absorber mount.
  2. Remove the wheel.
  3. Remove the upper shock nut, washer and bushing.
  4. Remove the lower mounting bolt(s) and remove the shock from the vehicle.
  5. Install the shock absorber in the vehicle and loosely tighten the upper shock absorber nut. Make sure the install the bushings and washers before installing the upper nut.
  6. For 4WD vehicles, install the shock absorber so that the white paint mark at the lower side of the shock absorber faces the outer side of the vehicle. Install the lower shock absorber bolt(s). On 1992-95 Montero torsion bar suspensions, tighten the single lower mounting bolt and nut to 65-76 ft. lbs. (88-103 Nm). On all other vehicles (whether torsion bar or coil spring suspensions), the two lower shock absorber mounting bolts should be tightened only to 7-10 ft. lbs. (9-14 Nm). Fig. 1: Install the shock absorber so that the white mark faces toward the outside of the vehicle - 4WD vehicles, except 1992-95 Monteros 86668006.gif
    Fig. 2: Install the bushings, washers and nuts in the order shown - except 1992-95 Monteros 86668007.gif

  7. On 1992-95 Monteros, tighten the shock absorber installation nut so that the dimensions shown in the illustration ( A and B) are at the standard values. These standard values are: A - 0.04-0.08 in. (1-2mm), B - 0.06-0.10 in. (1.5-2.5mm). WARNING
    When tightening the nut, be careful not to bend the stud pin of the washer assembly.
  8. On all other vehicles, once the lower mounting bolt(s) are tightened, tighten the upper shock absorber mounting nut all the way to the end of the thread on the shock absorber stud, then tighten the locking nut to 9-13 ft. lbs. (12-18 Nm).
  9. Install the wheel.
  10. Lower the vehicle to the ground. Fig. 3: When installing the upper shock nuts on 1992-95 Monteros, make sure measurement A is 0.04-0.08 in. (1-2mm) 86668008.gif
    Fig. 4: When installing the upper shock assembly, make sure its components are positioned as shown - 1992-95 Monteros 86668009.gif
prev.gif next.gif

Nov 03, 2010 | 1987 Mitsubishi Mighty Max

1 Answer

Thermostat for Nissan Pulsar 1992 Model


STANT REVERSE POPPET SERIES THERMOSTAT -- 195%XB0 F, A Direct Fit OE Replacement Engine Coolant Thermostat,
Thank you for using FixYa , Lee

Feb 22, 2010 | 1990 Nissan Pulsar

1 Answer

How do I remove the removable rear hatch?


Yea it does come off. I forget exactly how,kinda old & probably rotted enough to fall off,but if you insist.You raise the lid all the way & pull some pins out for the hinges & remove the gas struts that hold it up. There may be an electrical wire to disconnect too. Try the dealer for the exact instructions. Nissan will be around for many years unlike the American car makers.

Jun 28, 2009 | 1988 Nissan Pulsar

1 Answer

Where do i grease cv jionts on my pulsar n13 hatch?


get a needle (napa or autozone should have one) for the grease gun and poke the rubber and fill with grease and also try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 21, 2009 | 1988 Nissan Pulsar

1 Answer

Nissan pulsarGL N13 SHOCK ABSORBER


hi there it could be front shocks but do check it also could be the suspension bush normally the bottom one do worn out and do make that sound hope that helps i did change that on my mate car got the part from bnt

Jun 27, 2008 | 1988 Nissan Pulsar

Not finding what you are looking for?
1992 Nissan Sentra 4 Door Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...