Question about 1998 Jeep Grand Cherokee

Open Question

Repair rear diff on 98 jeep laredo - 1998 Jeep Grand Cherokee

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: brake pads specifications

I just searched google and looked at JC Whitney. They have brake parts and ship internationally. (don't know cost) But it's worth looking into!

Posted on Apr 30, 2009

  • 304 Answers

SOURCE: Rear Axel Seal Leaking, How do I pull the axel to repair?

You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

Posted on May 22, 2009

  • 316 Answers

SOURCE: Rear Diffrantial Leak 98' Ford Explorer

It should be that easy if the leak is from the gasket. If it from the seal, you will have to remove the drive shaft from the differential and remove the seal and put in a new one. Either way, the repair is fairly easy.

Posted on May 23, 2009

  • 6982 Answers

SOURCE: rear diff problem

The only place you did not mention is the pinion seal (at the yoke where the driveshaft connects) Any leak from a differential should be fairly obvious...clean everything off well and drive it, You should see seepage somewhere. Any grease on the wheels or new fluid where you cleaned will tell you where to look. If it is at the pinion seal, If you haven't done this before, don't...you can disturb the adjustment inside the gear case and damage the gears.

Posted on May 27, 2009

  • 6982 Answers

SOURCE: 98 jeep wrangler rear diff dana 35

Jack up both rear wheels then turn one by hand if the opposite wheel turns in the same direction you are turning it is a posi. If it either does not turn, or turns in the opposite direction it's not. (do this in neutral)
If still in doubt, have someone try to hold the opposite wheel and do it again. If they can hold the wheel without it turning it's not a posi.

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of all bearings on rear axle of 98 jeep grd cherk.limited 5.2L spicer 44


There will be one bearing pressed on each axle as well as two carrier bearings attached to the inner diff assembly. There will be two pinion bearings in the diff as well

Jan 05, 2016 | Jeep Cars & Trucks

1 Answer

I have a 1994 jeep grand cherokee laredo and everytime i drive for a period of time it feels like when i make turns something is rubbing or hesitating.


Contact the dealership and purchase the rear differential additive, this product assists the limited slip diff in opperating correctly. once purchased simply ad to the rear differential. it only takes about 250ml

Feb 14, 2011 | 1994 Jeep Grand Cherokee

1 Answer

I have bought a jeep grand cherokee laredo 98 and


Not if it locked mechanically. Ive had good luck using a pipe wrench sideways on the balancer to turn some over that were pretty frozen up.

May 07, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

What type of differential lube should I use


diff unit ,EP90 that will go in all of the differentials and manual gearboxes

Jan 08, 2010 | 2003 Jeep Grand Cherokee

3 Answers

Audible knocking in rear of 1993 jeep grand cherokee laredo with 150,800 miles knocking only occurs when accelerator is not pressed


Sounds as If You Have A Chipped Tooth On the "RING GEAR" in the Differential (Rear Alex).
Is this Where You Hear The Noise Coming from? If So Remove Diff Cover With One Wheel OFF The Ground Trans In Neutral Rotate Drive Shaft and Look Closely For ANY Abnormal Surface on EACH Tooth of RING GEAR= the Large one And The "PINION GEAR" the Small one. If you find Chip or Rough spot Diff Must Be Rebuilt. Beyond that A Pinion Bearing can Also Make A Knocking Noise But the "GEARS" Will Be a Rhythmic Noise. I Hope this is of Some Help To You Good Luck !!

Jun 03, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Rear diff problem


The only place you did not mention is the pinion seal (at the yoke where the driveshaft connects) Any leak from a differential should be fairly obvious...clean everything off well and drive it, You should see seepage somewhere. Any grease on the wheels or new fluid where you cleaned will tell you where to look. If it is at the pinion seal, If you haven't done this before, don't...you can disturb the adjustment inside the gear case and damage the gears.

May 27, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

4 Answers

Rear end (axle)


call jeep and give them last 9 digits of your vin and ask for three things -Differential Type,Gear ratio, and Track lock- They will give you
1) Dana 35 or 44
2) Gear Ratio 3.31 or 3.73
3) Track Lock - yes/no

Jan 11, 2009 | 1998 Jeep Grand Cherokee

1 Answer

How can i convert grand cherokee laredo from 2wheel to 4wheel.i wana ask you the process


First you need a transfer case, then you need a shorter rear drive shaft. You need a front diff. same ratio as the rear diff. you need a front drive shaft. You need different trailing arms. Should I go on ?

Dec 08, 2008 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...