Question about 1965 Ford Mustang

1 Answer

My air filter nut fell in to my carburater.is thier a way to get it out?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,918 Answers

Use a magnet

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Idle problem in nissan hardbody ka2400 16 valve


MAF sensor or idle jet dirty or clogged, a can of carburater cleaner through the intake after air filter (while reving) may clean it otherwise a service may be needed.

Jan 22, 2016 | 2007 Nissan Hardbody 3000TD

1 Answer

Where is the carburater


Careers are usually mounted on top of the intake manifold located on the top of the engine. It will be covered by an air cleaner box where the air filter is installed.

Oct 05, 2014 | Cars & Trucks

1 Answer

1999 GMC Suburban turns over but won't start


It sounds like the choke is the most likely culprit. Take the air cleaner off the throttle body/Carburater. Have someone cover most of the throttle body/Carburater intake, if you don't have help use a piece of heavy cardboard. If it starts up right away it's the choke. Note: if you use cardboard don't rev the engine you may **** the cardboard into the engine.
I'm afraid with all the different types of choke controls I can't tell you how to fix your choke with out actually seeing it.

Jun 06, 2010 | 1999 Chevrolet Suburban

1 Answer

2002 saturn columb is lose. need to pull steering wheel, but has air bag. never done it before.


Well , Let me start here if your saturn has tilt first check the lever that lets the stearing wheel go up and down . If that isnt the problem then first you need see if 1 the column its self is loose than you need to remove the plate were your hood release cable is located once you remove the 7mm bolts and the shield look under dash were stearing column is and thier is 4 13 mm bolts that actually hold it up tight against the dash if they are tight follow the stearing column down towards gas pedal thier are two bolts that that go through a bracket from left to right on one side its a 45 mm torxs male and a 14 mm nut check them for tightness if any are loose retighten to factory specs and use lock tight
to remove air bag first unplug batterie then thier are 4 slots on bach side of stearing column I use two flated head screw drivers and push one side and pull out gently once released do the other side the same way ,then thier will be a yellow plug unplug it and air bag is removed
from my experience if the bolts are tight u need a new stearing column witch you can buy used at a resonable price GASTON AUTO GASTON SOUTH CAROLINA i FOUND HAS THE BEST DEALS FOR SATURN
good luck if any other questions please feel free to ask ive worked on many saturns i love them little cars

Mar 26, 2010 | 2002 Saturn L-Series

4 Answers

How do you replace an air filter on a bmw 320d 2004 car


Maybe this guide can help you like a reference guide: Change Air Filter (with pics).

I hope help you (remember rated this help). Good luck.

Oct 02, 2009 | 2004 BMW 3 Series

1 Answer

Where is fuel filter in my 2005 camry


your filter should be visible from under the hood....or from under the nose of the car. will be bolted to the fender well.
0900c15280197a0d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Always use new gaskets when replacing a fuel filter


0900c15280197a0e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. A line wrench with an extension may be needed to loosen the inlet line at the filter-Corolla
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Protective shield for the fuel filter If necessary, air cleaner hose and cap If necessary, charcoal canister. Slowly loosen the lower flare nut fitting until all the pressure is relieved Banjo fitting and 2 metal gaskets. Discard the gaskets Fuel line with the flared nut from the filter Filter from the mounting bracket

To install:
  1. Install or connect the following:

    New fuel filter Banjo fitting with a new metal gasket on each side and install the union bolt. Bolt: 22 ft. lbs. (30 Nm). Flare nut to the lower connection. Nut: 22 ft. lbs. (30 Nm). Charcoal canister Air cleaner hose and cap Protective shield Negative battery cable

Jul 10, 2009 | 2000 Toyota Camry

1 Answer

1984 eldorado biarritz 4.1 engine Just bought it and it seems to run good, but when you come to a stop the engine will stumble, then idle will drop but not die. AC was running. Possible causes?. Put in...


check all vacuum hoses.if any looks cracked replace them.make sure carburater bolts are tight.check the egr valve make sure its not leaking.besure have your idle speed adjusted.it should be at 550 to 600 rpms.

Jul 10, 2009 | 1984 Cadillac Eldorado

2 Answers

Finding were a filter is


On these vehicles, the fuel filter is located on the fuel line to the carburetor. Special care should be taken when removing and installing the fuel filter, not to bend or distort the fuel line in any way.
  1. Remove gas cap to relieve any pressure that may be present in the fuel system.
  2. Remove the air cleaner bonnet assembly.
  3. Using a backup wrench on the return line fitting on the top of the fuel filter, remove the fuel line with a flare nut wrench.
  4. Using a backup wrench on the fuel filter inlet fitting, remove the fuel line from the fuel filter with a flare nut wrench.
  5. Using a backup wrench on the fuel filter outlet fitting, loosen the fuel line and remove the fuel filter from the engine with a flare nut wrench.
To Install:
  1. Apply a drop of engine oil to all the fuel line nuts and flared ends.
  2. Position the fuel filter with flow arrow on the filter directed towards the fuel line going to the carburetor.
  3. Finger-tighten the fittings at the fuel filter outlet, inlet and return line into the top of the filter.
  4. Using a backup wrench on the fuel filter fittings, tighten the fuel lines in the following sequence:
    1. Tighten the outlet and inlet line nuts to 15-18 ft. lbs. (20.0-24.0 Nm)
    2. Tighten the nut on the return line at the top of the filter to 6-9 ft. lbs. (15-18 Nm).
  5. Inspect the fuel lines and carefully adjust if they are interfering with the carburetor, air pump, or fuel filter housing.
  6. Start the engine and check for fuel leaks at all the connections. Retighten if necessary.
  7. If removed, install the air filter bonnet assembly.
0900c1528005d3e1.gif 0900c1528005d3e3.gif

Jul 26, 2008 | 1993 Ford Tempo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...