Question about 1993 Isuzu Trooper

1 Answer

Are isuzu headlights sealed beam or can u just replace bulb

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Replace bulb

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace headlights on 1989 toyota camry


1989 Toyota Camry

A little personal tip - if you get fingermarks on a halogen headlamp, you can wipe them off with rubbing alcohol (isopropyl alcohol) or, if you want to do what mechanics do, keep a number of 2X2 alcohol wipes in your automotive toolbox just to wipe off halogen headlight bulbs.

HEADLAMP REMOVAL & INSTALLATION

Sealed Beam Headlamps

See Figures 2 and 3

Before making a headlight replacement, make sure that the headlight switch is in the off position.

1. Loosen the screws, release the clips and remove the headlight door. To release the clips, insert a flat blade screwdriver into the jaws of the clip and pry on the jaws.

2. Remove the beam unit retaining ring screws and remove the beam unit.

Fig. 2: Headlamp door clip removal

3. Compress the lock releases and disconnect the wire connector from the headlight. If the connector is tight, wiggle it while holding in the lock releases and pulling out.

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb

Never try to loosen the aim adjusting screws. If the screws are loosened, the headlights will have to be re-aimed by a qualified technician.

4. When installing, use only a sealed beam unit with the same part number and wattage.

Composite Headlamps

See Figures 4, 5 and 6

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment

Fig. 5: Detach the wiring from the back of the headlamp bulb

This procedure only applies to replaceable halogen headlight bulbs (such as Nos. 9004 and 9005); it does not pertain to sealed beam units.

1. Open the vehicle's hood and secure it in an upright position.

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good

2. Unfasten the locking ring which secures the bulb and socket assembly, then withdraw the assembly rearward.

3. If necessary, gently pry the socket's retaining clip over the projection on the bulb (use care not to break the clip.) Pull the bulb from the socket.

To install:

4. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.

5. Line up the replacement headlight bulb with the socket. Firmly push the bulb onto the socket until the spring clip latches over the bulb's projection.

WARNING
Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.

6. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.

7. Position the headlight bulb and secure it with the locking ring.

8. Close the vehicle's hood.

Fig. 1 - various automotive lamps

10_4_2011_8_32_12_pm.jpg

Fig.2 - Headlamp Door Clip Removal

10_4_2011_8_32_40_pm.jpg

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb


10_4_2011_8_33_24_pm.jpg

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment


10_4_2011_8_33_51_pm.jpg

Fig. 5: Detach the wiring from the back of the headlamp bulb


10_4_2011_8_34_22_pm.jpg

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good.

10_4_2011_8_34_49_pm.jpg

Oct 03, 2011 | 1989 Toyota Camry

1 Answer

How to replace low beam bulb


There are two primary headlight systems. The first is a seal beam unit and the second is a headlight bulb. For the seal beam unit you have to remove the outside trim. There are usually a couple of screw holding the trim in place. Do not confuse this with the headlight alignment or adjustment screws. Once the trim is removed the headlight can be pulled out and then unplugged. Reverse the process to install. To replace a headlight bulb you open the hood . On the back side behine the headlight there should be a cap or plug with a couple of wires running thru it. You twist or pop this off and should then be able to pull the headlight bulb out. Pull the bulb from the plug connector. Holding the new plug with a clean lint free cloth (don't handle the bulb with your bare hands as it will cause it to burn out early), install the bulb in the plug. reverse to install

Feb 20, 2010 | 1998 Oldsmobile 88

1 Answer

How to change headlight


This is the same for the pick up as is the Trooper:

Aerodynamic Type

e5d8044.gif
Replacing a headlamp bulb—1994 Trooper shown


8391601.gif
Replacing a headlamp bulb—1994 Trooper shown


  1. Disconnect the negative (−) battery cable.
  2. Open the hood and disconnect the headlight bulb electrical connector.
  3. There are two possible designs. For the first design, turn the bulb to remove it from the housing, for the second unscrew the retaining cap and remove the bulb.

    WARNING Do not touch the glass portion of the halogen bulb. Any contamination on the bulb may cause the bulb to burst when turned ON. If the bulb is contaminated, clean the glass portion with rubbing alcohol.

  4. Hold the bulb by the plastic portion only. Install the bulb and connect the wiring harness. Make sure the sealing ring is in place.


Non-Aerodynamic




3dbcbc6.gif Replacing a sealed beam headlamp—1990 Amigo shown

  1. Disconnect the negative (−) battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.

Feb 14, 2010 | 1994 Isuzu Pickup

1 Answer

Low beam Headlights out. Not the fuses or the


Hi, check the low beam relay, relay's for the headlights should be either near the fusebox, or under the engine compartment, if not this may be hi/lo beam switch, hope this helps :)

Dec 26, 2009 | 2007 Isuzu Ascender 7 Passenger

1 Answer

Replacing low beam headlights


if equipped with sealed beam lights,remove screws from trim panel surrounding headlights.remove 4 screws from headlight bezel [silver rectangle that retains bulb] unplug connector.do not remove adjustment screws. halogen bulbs may be reached from engine compartment,behind light assembly.

Oct 13, 2009 | 2000 Chrysler Town & Country

2 Answers

Replace highbeam 1996 rodeo


LIGHTING Headlights REMOVAL & INSTALLATION Non-Aerodynamic
Fig. 1: Replacing a sealed beam headlamp

bd06397.gif
  1. Disconnect the negative battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.
Aerodynamic

Fig. 2: Replacing a headlamp bulb

cf46ef4.gif

Jul 24, 2009 | 1996 Isuzu Rodeo

1 Answer

1996 CAMARO BLOWS HEADLIGHT EVERY 6 MONTHS


ive had 2 camaros and both did this. remove the headlight and take the bulb out of the back of the sealed beam. be careful not to break it as its glued in, but it is possible. just be gentle and patient. replace the bulb with an aftermarket 9006 bulb (hi beams are 9005) and silicone it back into the housing. i haven't had one burn out yet after doing this

Jun 28, 2009 | 1996 Chevrolet Camaro

1 Answer

Low headlights do not work


Check your hi/low beam switch. It sounds like you are not getting power through the switch on low beams.

Dec 29, 2008 | 2000 Isuzu Amigo

1 Answer

Headlights don't work


Try replacing the bulbs in the sealed beam. Bulb #9007, do both. Lift lid, disconnect electrical wires, unlock o ring, pull out bulb. Replace bulb and reverse the order

Dec 03, 2008 | 1995 Mercury Villager

1 Answer

Seal beam doesn't light


You should be able to replace just the headlight bulb itself, most cars haven't had sealed beam headlights since the '80s. Assuming that's what you mean by "seal beam". Is it the main beam/dip beam, the high beam, or is it a driving light/fog light (usually mounted down low in the bottom of the front bumper area)?

Oct 21, 2008 | 1999 Nissan Sentra

Not finding what you are looking for?
1993 Isuzu Trooper Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...