Question about 2000 Hyundai Elantra

1 Answer

I just changed the trans and now the clutch will not engage on 2000 Elantra?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Has the release yoke slipped off the release bearing?

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Hyundai elantra shifts into overdrive but just slips.


Do you have a check engine light on? Any fault codes?

Jun 08, 2016 | 2000 Hyundai Elantra

1 Answer

How do I fix 2005 hyudai elantra gt 5 speed.


they have to be in nneutral or the clutch has to be pushed in to keep you from running into or over people

Mar 09, 2015 | 2005 Hyundai Elantra GT

1 Answer

Clutch is slow to engage when I stomp on the gas


If you have a cable operated clutch system then replace the cable as it is failing. If you have a hydraulic clutch the replace the clutch master cylinder as there is a blockage in the compensating port.

Sep 14, 2013 | 2000 Hyundai Elantra

1 Answer

Stiff clutch on 2002 elantra , clutch and transmission new , slave clinder pushes wrong way ,whats wrong ?


FYI, the slave cylinder is pushing correctly, the clutch is the 'PULL TYPE', not the 'PUSH' type.
Go to www.hmaservice.com and register the vehicle by VIN #. You'll then have access to Shop Manuals, Wiring Diagrams, Illustrations, Service Bulletins, etc.

The clutch on the 2002 Elantra, as I mentioned, is the "Pull Type". Instead of 'Pushing' on the throw-out bearing, it "Pulls" on it. The pressure plate engages when the bearing is released (when it is 'pulled' back into the pressure plate 'fingers'

Was the new trans & clutch installed at an authorized Hyundai Service Department? If not, you might want to have them inspect the installation to determine what's wrong. If it WAS installed by a Hyundai Service Dept, take it back to them & tell them to FIX IT!

Jun 30, 2011 | Hyundai Motor 2002 Elantra

2 Answers

How do I remove tranny and clutch seems stuck on the engine 2000 hundai elantra manuel I can get it off about a half inch and it stops


the clutch is a pull type, not a push type, to remove the trans you have to remove the release fork lever, to do that fist remove the clutch slave cylinder, then remove the 14mm nut tha holds the fork arm, then you can remove the trans, however reassembly is a whole nother complicated story.

Nov 18, 2009 | 2000 Hyundai Elantra

1 Answer

Trans drops into 3rd gear won,t shift to 4th


DTC P0734 is "4th gear incorrect ratio" - that's your torque converter 'LOCK UP Clutch" It's worn out (or you're using the wrong Trans Fluid required by Hyundai - SPIII OR Both). The P1624 is simply the Trans Control Unit (computer) communicating to the Engine Control Module (ECM computer) MIL - on request signal to ECM = asking it to turn on "Check Engine" light. MIL = Malfunction Indicator Lamp. When the torque converter 'lock up" clutch slips or doesn't engage, the trans automatically returns to 3rd gear and stays there (it's called 'fail safe' mode) until you cycle the ignition key, then everything resets until the malfunction occurs again.
You'll need to have an AT (Automatic Transaxel) tester hooked up to verify this. Hyundai has a Service Bulletin specifically for "gear incorrect ratio' codes. If when you changed the trans fluid, was it done at a Hyundai Service Center? If not, someone may have installed the wrong fluid.

Jun 01, 2009 | 2000 Hyundai Elantra

2 Answers

2000 Elantra manual trans car won't crank


While the suggested resistance check of the clutch safety switch should catch a bad switch. However it may still be bad. I had the experience on my 2001 Elantra with the same problem happening intermittently. I checked and I had the delay check the switch and it looked okay. After three more trips and having them test other things including replacing the Starter motor under warranty they just replaced the switch. No more problem until 3 years later same thing started happening. I asked them to specifically check this and they just adjusted how far the switch button stuck out for teh clutch pedal to engage it under the dash. 4 days later it happened again. I said f it or something like that and went and bought the 15 dollar switch and put it in myself. I've not had a problem since then. But then I'm just coming up to the 3 yr anniversary of that switch.
You can also just bypass the switch and remember not to crank your starter without the clutch engaged unless you want to experience what whiplash is like firsthand.
Just change the switch.

Jan 15, 2009 | 2000 Hyundai Elantra

2 Answers

2000 Hyundai Elantra Transmission problem


I don't know if I can help but as an owner of a Hyundai Elantra 2000 GLS with 205,000 miles and the original clutch and transmission I'll try and help!

I always start with the lowest cost solution first and avoid mechanics as much as possible!

Have you checked the trans fluid?
It should be changed every 30,000 miles!
Sometimes a Lucas Trans Fluid will cure - fix slippage!

Have you checked for a clutch adjustmet!
An adjustment can cure - fix slippage!

Are you a clutch rider with your foot always on the clutch?
If so you may have worn out the clutch!

How many miles to you have on your Hyundai Elantra 2000?

Jan 12, 2009 | 2000 Hyundai Elantra

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...