Question about 1996 Isuzu Trooper

2 Answers

Is the rear wheel bearings presses on

Is the rear wheel bearings pressed
on

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,051 Answers

Hello there:
at the factory the original bearings are filled with high quality grease and pressed in using a slight amount of presure thus making it removable and replaceable nowdays bearings are removed with a tool and replaced in with a tool that any body can get or rent from a autozone or a kragen to use on their vehical ok
I hope this is very helpful for you
Best regards MIchael

Posted on Apr 24, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 2,100 Answers

Yes they are , but they are not extreme, you can get them off with a little effort. If they burned up, they may have welded them selves to the axle, then you will have to cut them off. Not with a torch, even though it will work, but with a dremel with a cutoff wheel, or a bunch of them. Hope this helps.

Posted on Apr 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I remove rear outer bearing?


New style bearings are all pressfit bearings, if your hub came right out of the bearing assembly, it is time for the whole assembly. The hub assembly has a locking ring that holds the outer bearing race inside the hub, after the wheel hub has been pressed out. Then, after the lockring has been removed it can be pressed out and the new bearing can be pressed back in and then the lockring reinserted. Then the wheel hub gets pressed in.

Mar 05, 2016 | 2002 Kia Sportage

1 Answer

Replace wheel bearing


which wheel bearing front rear on the front with front wheel drive you will need to remove the steering knuckle and then press the bearing out with a shop press then press hub back in to bearing on the rear it is most likely a bolt in easy

May 28, 2013 | 1989 Cadillac Sedan DeVille

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

4 Answers

The right rear wheel of my 1991 Justy 4wd sways and made noise on the road. What would be the problem thanks


the rear Hub bearing is out!! need to jack it up take the wheel off and the caliper and disk and replace the bearing if it has drum brakes which is should!! you will have to pull the axle to get to the bearing

Jan 17, 2010 | 1991 Subaru Justy

4 Answers

Have 2002 ford explorer,right rear wheel feels loose. checked lugs, all tight, pulled wheel and rotor is wobbly, losse. what's the cause?


You need a wheel bearing....don't drive it. Tow it to a dealer.! Ford wheel bearings are cheaper than aftermarket.
250-300 dollar fix.

Dec 31, 2009 | 2002 Ford Explorer

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

1 Answer

Need to see a diagram of how to change rear wheel bearing on my 320 touring 1996


BMW uses CV shafts for the rear drive axle, the wheel bearing there is a pressed in factory sealed bearing and not removable other than using a press to remove it, to press it you will need to remove the lower control arm.

May 22, 2009 | 1999 BMW 323 Series

1 Answer

Rear Wheel bearing needs to be replaced


the bearing has to be pressed in, quite the job even doing it at the shop- you will have to have some sort of press to press the bearing in.

May 20, 2009 | 2001 Ford Escape

Not finding what you are looking for?
1996 Isuzu Trooper Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...