Question about 2003 Chevrolet Impala

1 Answer

What bolt do i need to loose on an 2003 chevrolt impala for the fan belt

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

The two bottom holding bolts on the alternator and the two bolts on the adjusting arm(once loose and the correct flex of the belt is achieved do up the adjusting arm then the two holding bolts.

Posted on Apr 24, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 impala rear of car kicks out around turns feels like car is dog tracking but coil springs look okay

Look for loose parts, loose front carriage bolts, suspension bolts or wear, and don't forget to make sure that tires are all the same size and that the wheel bearing are all good. This can be a difficult thing to find, but these are good places to start.

Oct 26, 2011 | 2003 Chevrolet Impala

1 Answer

How do I replace the battery in my 2003 monte carlo? I removed the 2 wire bolts but it feels tight to the bottem as if it is clamped in... what am i missing?

It should be similar to my Impala. There is a clamp wedge held in by one bolt. It is probably in the middle of the two wires (cables), down at the base of the battery. Remove the bolt and the plastic(?) wedge and the battery will be loose.
(On my Impala, I also have to remove the cross bar that passes over the battery.)

Aug 09, 2011 | 2003 Chevrolet Monte Carlo

1 Answer

I have a 2003 Chevy Venture and we replaced the belt, the tensioner and the powersteering pump and the belt still keeps coming off. What could be the cause?

One or more of the pulleys are out of alignment. It may be caused by a bad bearing in one of the pulleys or loose bolts holding them in place. Check all the adjusting bolts and the bolts holding the belt on things like the crank, fan, alternator, etc.

Dec 19, 2010 | 2001 Chevrolet Venture

1 Answer

How do you change a blower motor on a 2003 chevy impala?

remove glove box for access remove power plug on fan , remove bolts ,some are hard to get to,fan assembly should twist out

Nov 16, 2010 | 2003 Chevrolet Impala

1 Answer

Where is tensioner for altenator fan belt

the alternator holding bolts are to adjust the belt tension...wedge something behind the alternator, when loose,then tighten when correct.

Apr 26, 2010 | 2003 Kia Sedona

1 Answer

How do I remove the fan belt tensioner on a 03 ford ranger 3.0

all u have to do is take the belt loose look at the tensioner and just see if it has a bolt or whole on the bottom of it when u pull on it will pull over then u slide the belt off then take the bolt out thats above that one and tensioner will come over just revere to install new tensioner be sure to have the alighnment notch on the back of the tensioner in the right whole

Mar 14, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Have to bang on dash to get blower to come on 2003 impala

You have a loose wire connection from the fan switch to the motor someplace. Banging on the dash makes temporary connection of the loose connection problem until the next time you try it. It is possible too that your fan switch is corroded.

Dec 07, 2009 | 2003 Chevrolet Impala

2 Answers

Serpentine belt diagram for 2003 chevy impala

send an email to and I will send the diagram to you

Jun 23, 2009 | 2003 Chevrolet Impala

1 Answer

How to change fan belt on v6

you will need to remove the tensioner to remove belt 2 12mm bolts.

Feb 08, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Chevrolet Impala Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides