Question about 1994 Mazda 929

1 Answer

What does it mean when i have to let off the gas at 2000rpm to allow transmisson to shift?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 2,002 Answers

It could be a lot of things. First, check the fluid level to make sure it's full. Low fluid can cause it.
Second, when is the last time you changed the fluid? It usually shoul be done around the 60,000 or 70,000 mile mark. there could be a build up of sludge and filings that are rstricting passages. If it hasn't been done then I would get it flushed when the fluid and filter are changed.
Third, it could be wearing out. It has clutches inside and they wear every time it shifts.The only thing you can try, short of a rebuild is an additive to the fluid, like Lucas to try and extend the life of the transmission, but that is only a temporary cure. It will have to be replaced or rebuilt.
Fourth, it could be something mechanical, but you'll probably have to take it to a shop to get an accurate diagnosis of that.
Hope this helps.

Posted on Apr 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 chevy impala started jerking and then it wouldnt chnage gears unless i press the gas all the way to the floor is it the transmission?


no on 05 chevy the transmisson shift is control by vacume look for a vacume line that is dry rooted or has come off start at the engine first then work the way down to the transmisson. a line off or dry rotted any where in the syastem will give you a hard shift sometiimes like a hard jerking motion when
shifting.

Aug 10, 2011 | 2005 Chevrolet Impala

1 Answer

My automatic trans is not shifting correctly after we replaced the engine'I. It is hard to go to 2nd and if it goes to 3rd a little gas and it downshifts back to 2nd. We changed the filter and new fluid...


You need to adjust you shift linkage, and I would recommend that you run some Seafoam in your transmisson, it will stop hard shifts, and restore your shift points.

Mar 23, 2011 | 1986 Pontiac Fiero

1 Answer

I cant find were the transmission control solenoid is located at and need to replace it


what kind of transmisson is this 4t40or 4t60 or 4t65 or 4L60 ..well most general motor solenoids are located on the the transmisson valve body . which means on a rear wheel drive the transmisson pan needs to be remove to gain access to the valve body . On a front wheel drive the valve body is located under the side cover on the transmisson . Now if i remember rigth there are 3 or 4 control solnoids . 1-2 shift 2-3 shift and a Tcc solnoid . you need to know which one to replace and what location are they on the valve body

Mar 06, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

After warm up the transmission will not always shift up into Drive and overdrive causing the engine to race.


try checking the fluid level if it is even aa half pint off it can cause shift problems, if it is low add some Lucas transmisson oil condtioner this will help it shift smoother. also look at the color of the fluid is it brownish in color? if yes then it's time to change the filter and fluid. if you take it to a shop they chagre about $150.00 but it will keep you from damaging the transmisson. the oil and filter for the transmisson should be changed every 30,000 miles on any car. Thisis oone of the most overlooked items of maintence on cars peopel simply don't know about change the filter and oil till they have to pay for a new transmisson.

Nov 09, 2009 | 2003 Jeep Grand Cherokee

1 Answer

My 2004 for F-150 Herittage only has 32,000 miles on it. I wont work in reverse and wont shift out of first gear. What could the problem be. The shop where its at cant figure it out, they said its not the...


There could be several but It should have 100,000 mile warrenty on the drive train so take it to the dealer Your truck is notthe first one I have seen on here with this problem and always assumed it was a transmisson problem. I ned to know how they know it's not the transmisson? did they remove the shift lingange offf the transmisson and see if it would shift thru the gears ? Also Ford has it's powertrain control module mouned in the transmisson so this does not seem right to me, ask them if they took the linkage off and tested the control module and get back to me.

Sep 16, 2009 | Ford F-150 Cars & Trucks

1 Answer

Automatic transmission shutters on 1-2 shift when warm


change the transmisson oil and filter and all oil, about 12 quarts and add 1 quart of lucas transmisson condtioner to soften the seals and bands and clutchs and clean the shafts on the shifting valves.

Jun 25, 2009 | 2000 Kia Sephia

1 Answer

TRANSMISSON PROBLEMS


if its manual sounds like your clutch could be slipping does car smell of burt clutch?
check cluth adjustment
may need new clutch
do stall test with hand brake on, foot (heel-toe) on brake and accel pedal to about 2000rpm then let out clutch and car should stall if engine revs go down and engine still runs but you can rev causing slip and you will now smell what slipping burnt clutch is replace it.

if its auto check trans oil level and what does it look like red-good
darker red to black-bad often smells burnt also possibly new trans required.

May 31, 2009 | 2000 Toyota Celica

1 Answer

Locating the shift solinoid on 1991 olds cutlas ciera


it's inside the transmisson you have to remove the oil pan on the transmisson to get to it.

May 28, 2009 | 1991 Oldsmobile Cutlass Calais

1 Answer

Transmisson will not shift out of sport


does it shift through it's gears? 1st ,2nd,3rd? if it dosn't then the tcu is burned out a common problem for 91-93 accords

Apr 17, 2009 | 1991 Honda Accord

2 Answers

Chrysler concorde doesn't shift out of first


It sounds like it is in limp mode, this means that there is a transmission problem. The trans will go into limp mode to protect from further damage. You need to take it to a trans shop to have diagnostic test

Mar 04, 2009 | 1998 Chrysler Concorde

Not finding what you are looking for?
1994 Mazda 929 Logo

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...